Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.
- Sailboat Guide
Bayfield 29
Bayfield 29 is a 29 ′ 0 ″ / 8.8 m monohull sailboat designed by Ted Gozzard and built by Bayfield Boat Yard Ltd. between 1980 and 1983.
Rig and Sails
Auxilary power, accomodations, calculations.
The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.
Classic hull speed formula:
Hull Speed = 1.34 x √LWL
Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio .311 Hull Speed = Max Speed/Length ratio x √LWL
Sail Area / Displacement Ratio
A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.
SA/D = SA ÷ (D ÷ 64) 2/3
- SA : Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
- D : Displacement in pounds.
Ballast / Displacement Ratio
A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.
Ballast / Displacement * 100
Displacement / Length Ratio
A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.
D/L = (D ÷ 2240) ÷ (0.01 x LWL)³
- D: Displacement of the boat in pounds.
- LWL: Waterline length in feet
Comfort Ratio
This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.
Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam 1.33 )
- D: Displacement of the boat in pounds
- LOA: Length overall in feet
- Beam: Width of boat at the widest point in feet
Capsize Screening Formula
This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.
CSV = Beam ÷ ³√(D / 64)
Embed this page on your own website by copying and pasting this code.
- About Sailboat Guide
©2024 Sea Time Tech, LLC
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Bayfield 29
The bayfield 29 is a 29.0ft cutter designed by ted gozzard and built in fiberglass by bayfield boat yard ltd. (can) between 1978 and 1983., 350 units have been built..
The Bayfield 29 is a heavy sailboat which is a good performer. It is very stable / stiff and has a low righting capability if capsized. It is best suited as a coastal cruiser. The fuel capacity is originally very small. There is a very short water supply range.
Bayfield 29 for sale elsewhere on the web:
Main features
Login or register to personnalize this screen.
You will be able to pin external links of your choice.
See how Sailboatlab works in video
We help you build your own hydraulic steering system - Lecomble & Schmitt
Accommodations
Builder data, modal title.
The content of your modal.
Personalize your sailboat data sheet
BAYFIELD 29 Detailed Review
If you are a boat enthusiast looking to get more information on specs, built, make, etc. of different boats, then here is a complete review of BAYFIELD 29. Built by Bayfield Boat Yard Ltd. (CAN) and designed by Ted Gozzard, the boat was first built in 1978. It has a hull type of Long Keel and LOA is 8.84. Its sail area/displacement ratio 20.33. Its auxiliary power tank, manufactured by Yanmar, runs on Diesel.
BAYFIELD 29 has retained its value as a result of superior building, a solid reputation, and a devoted owner base. Read on to find out more about BAYFIELD 29 and decide if it is a fit for your boating needs.
Boat Information
Boat specifications, sail boat calculation, rig and sail specs, auxillary power tank, accomodations, contributions, who designed the bayfield 29.
BAYFIELD 29 was designed by Ted Gozzard.
Who builds BAYFIELD 29?
BAYFIELD 29 is built by Bayfield Boat Yard Ltd. (CAN).
When was BAYFIELD 29 first built?
BAYFIELD 29 was first built in 1978.
How long is BAYFIELD 29?
BAYFIELD 29 is 6.63 m in length.
What is mast height on BAYFIELD 29?
BAYFIELD 29 has a mast height of 9.3 m.
Member Boats at HarborMoor
Review of Bayfield 29
Basic specs..
The Bayfield 29 is equipped with a long keel. A long keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.
The boat can enter even shallow marinas as the draft is just about 1.07 - 1.17 meter (3.51 - 3.81 ft) dependent on the load. See immersion rate below.
The boat is typically equipped with an inboard Yanmar 2GM diesel engine at 15.0 hp (11 kW), which gives a max speed about 5.0 knots.
The fuel tank has a capacity of 76 liters (20 US gallons, 16 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Bayfield 29 is 2.12, indicating that this boat would not be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 6.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Bayfield 29 is about 137 kg/cm, alternatively 771 lbs/inch. Meaning: if you load 137 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 771 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
What is L/B (Length Beam Ratio)?
What is a Ballast Ratio?
What is Displacement Length Ratio?
What is SA/D (Sail Area Displacement ratio)?
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 14m 2 (150 ft 2 ). Based on this, your favourite maritime shop can tell you the quantity you need.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.
We are always looking for new photos. If you can contribute with photos for Bayfield 29 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us . Criticism helps us to improve.
Bow and Stern
Adventures in a bayfield 29.
Bayfield 29 — An early review
I’ve had a few weeks with the new boat (Bayfield 29, la Princesa …until I change the name in a few weeks), and I’m getting a good feel for her.
Firstly, I don’t have any buyers remorse. At least not yet. I’m rather pleased with the design in general.
Under sail:
She sails remarkably well in light air. Not race boat fast; but certainly a lot better than I expected from a full keel, rather full body cutter. Under the asymmetrical spinnaker she would do three knots in around six knots indicated wind (masthead anemometer), and if I was willing to settle for two knots of speed (and I often am), I could probably keep her moving at that pace on most points of sail under working canvas in any but the lightest wind (perhaps I’m overstating the case; but given my experience so far I don’t think by much).
She is perfectly happy in heavyish weather provided she gets a reef in the main by around 20 knots wind or so. I’ve had her in the high twenties pushing thirty (apparent, indicated) under one reef and both head-sails (I’m not sure if they are the original sizes or not) and there was a fair amount of weather helm; but it wasn’t unmanageable or uncomfortable, although a second reef probably wouldn’t have been a bad idea. I haven’t explored the full range of capability yet (I JUST bought the boat); but I’m willing to bet that with the second (fairly deep) reef, 40 knots of wind will be somewhat anti-climatic (although the wave action that goes along with 40 knots might not be pleasant…I’m not rushing to find out). I find her quite stiff (a benefit of that rotund body, I suspect), dry, and comfortable throughout the twenties with probably three to four foot Chesapeake waves.
Under Power:
No trouble handling under power in forward. She will turn within her own length to port (edit: I THINK to port…My recollection is suddenly challenging that direction). In reverse I now understand all the full keel complaints. I’m sure I’ll figure it out eventually; but I haven’t yet. I back into my slip; but I am using warping lines more than engine power at the moment. It’s a bit more work; but even single handed in a cross breeze I know I can get the boat in that way. I have watched some maestros under power, though, and I know it can be done with some more experience.
Cockpit and Deck:
The cockpit is deeper than I would like. It feels quite secure; but I need a huge cushion to sit high enough for good visibility (and I’m not a tiny man!). The seat coamings are practically vertical, the seat bottoms are too narrow, and the foot well area is so wide it is difficult to brace against the opposite seat. Happily, with the cushion I’m high enough I can see, and the boat is stiff enough that bracing isn’t as big a deal as it could be. But if each of the seats was a few inches wider, and the foot well was 6-8 inches narrower, and the back rest was angled a bit, the cockpit would be much more comfortable. Also I find it a little tricky to have one person at the tiller while another is tending the sheets as they both want to occupy the same space. This can be worked around, and with experimentation I am figuring it out; but some more thought here wouldn’t have been out of place. The cockpit also seems designed to hold a tremendous amount of water, with only two average size (1.5″ maybe? Less?) drains to let it all out. Hopefully if I’m ever out in conditions likely to flood the cockpit the cabin hatches are in, and the engine room hatch gasketing is more robust than it looks. Before serious contemplation of an offshore trip I’d have to think long and hard about putting in more cockpit drainage. As deep as the cockpit is, boat handling would be a challenge with more than a couple people in it.
While we are in the cockpit, I’d also like to say that I am not a big fan of having halyards run aft. Running the two head-sail halyards aft is pointless because I have roller furling (which is pretty nice, by the way). And the mains’l halyard is almost as pointless as the main seems to often get hung up on the lazyjacks going both up and down, which requires going to the mast to guide things along. While this is probably correctable either through a reconfiguration of the lazyjacks, or a change in technique on my part, what is not easily correctable is the reefing lines which are at the base of the boom. There is little point in trying to rig them to the cockpit as it is still necessary to be at the mast to get the reefing hook into the tack (although I suppose I could try and rig single line reefing…I’ll think about it). The outhaul and topping lift are also controlled at the mast. What the heck, they might as well have left the main halyard there too! I’ll think about it for the next year or so, I guess, and see if it bugs me enough to make changes. This is one of those things where the current setup appears ideal for the single hander, but I find it quite the opposite. It’s also a shame the boom wasn’t a few inches higher as this is a headache waiting to happen (a foot higher might permit standing headroom under the dodger and bimini)!
One other gripe, although this seems to also be common across most modern designs, is that one of the shroud chainplates on either side goes through the deck. The inner shrouds are attached to the house sides, and with that near vertical orientation they don’t seem to leak. The outer shrouds, though, poke a hole through the damn deck. Why? This is certainly NOT a racing boat, so a couple extra inches of sheeting angle won’t matter, especially since neither head sail extends aft of the mast. If Bayfield would have just moved the chainplates to the hull side I’m willing to bet that any water leakage, even with old caulking, would be minimal. As it is I’m going to need to caulk them up when I do my winter refit. The standing rigging will need to be replaced at some point, and I may consider moving those chain plates out at that time. I need to do research first, though, as there are likely to be unintended consequences.
The good news is the side decks are reasonably wide, the life lines are high enough to be safe, the foredeck feels secure, and the motion of the boat is quite comfortable.
Moving on to the interior we have what is, in many ways, a brilliant layout. By eliminating the v-berth (which typically in small boats becomes a catch all junk room) we not only get rid of the least comfortable berth aboard, we suddenly have room for a remarkably spacious head for a small boat. It is quite comfortable. Forward of the head is a hanging/storage locker, and further forward a huge anchor locker. There is even a funny little cushioned seat in the head, which I haven’t been able to find a point to; but it looks pretty cool even if I’m unlikely to ever sit on it. With the head further forward, we open up the main cabin. There is a centerline table with fold up leafs. On the starboard side is a berth that pulls out into a double, with a regular settee on the port side. Aft further is a half bulkhead that separates the galley (starboard) and chart table (decently sized to port). Partitions slide up from the half bulkhead to really separate the main cabin from what I’m calling the “working” (galley/navigation) cabin if the need for privacy and separation would arise (for instance, on a passage with sleeping crew). Aft of both the galley and chart table are a pair of quarter berths, port (a little too short) and starboard (plenty long). Four opening portlights plus the hatch in the head allow for decent ventilation. I’m 5’10” tall and I have standing headroom throughout, barely, although I have bumped my head a few times walking through the door to the head. Stowage is quite reasonable (I’m still experimenting on how best to utilize it). Water tankage is fine for a week or so (25 or 30 gallons I’m guessing); but could probably stand to be increased for any extended trips, especially considering the waste associated with a pressure water system (there is currently no system implemented for non-pressure water, although this is on my to-do list). The interior is teak, which some people like (me, for one), and others find gloomy. Build quality seems generally very decent.
Brilliant or not, I have a couple gripes about the interior as well. Well, I have one BIG gripe. Once again Ted Gozzard (or perhaps Bayfield yachts themselves) had an ergonomic brain fart. The settees, when in “couch” mode (that is, the seat backs are down), are too narrow, and it constantly feels like you are sitting on the edge of your seat. I guess this is OK for eating at the table; but not my cup of tea for just relaxing in the cabin. Raise the seat backs into bunk mode and they are as comfortable as any bunk I’ve personally been on. I have a few thoughts on how to make the settees more comfortable; but it will take a little experimentation. I’m going to try to avoid major surgery, or having to make new cushions ($$$); but I might not get away with that. Given that this boat will eventually be my home, though, the situation needs to be worked on a bit, and it deserves to have a few dollars thrown at it.
Ice melts fast in the ice-box. I think I’ll probably turn it into dry storage and pick up an Engle or something (I’ll snug it down into the starboard quarter berth or something, I guess).
Mechanicals:
The engine is a Yanmar 2GM, is about thirteen horsepower (although I can not get it up to max continuous RPM of 3400, meaning I’m not getting all the ponies), and seems to push the boat along just fine. When the wind and seas are calm I am just about getting to hull speed at maybe 2800 RPM (indicated). When the wind and waves are well up, I’ve been held back to as little as four knots over the ground (the knotmeter is not giving realistic numbers, so I’m defaulting to GPS…it should be correct within a quarter to maybe half knot or so, I think) at my max achievable RPM of three thousand. A few extra horsepower when the wind is blowing would not be unwelcome; but I think I’m getting an adequate amount. I think twenty horse power would have been a better choice; but not nearly better enough to consider spending the money to repower. I haven’t figured out fuel consumption, yet; but it is modest. The standard alternator is 35 amps. Given the horsepower, I’m not sure if it is reasonable to go much bigger which might put a practical limit on battery capacity.
Engine access is terrific, both through a hatch in the cockpit (although I wonder what would happen if the cockpit got flooded) and by removing the companionway steps, through the cabin. My only complaint is that the oil dipstick is in an awkward location which discourages checking it daily; but that is part of the discipline. I had a cooling problem a few days ago, so I pulled the water pump off to check the impeller and replace the belts. It was easy. I haven’t done any other maintenance on it yet; but outside of changing the oil (I think the old oil is sucked up through the dipstick port with a pump), most everything looks pretty easy to handle. Since there isn’t an hour meter on the motor and I don’t know when any scheduled preventative maintenance was last done, I’m planning on doing pretty much everything on the scheduled maintenance list to effectively reset the clock to zero before hauling in a few weeks for the winter. I may put in an hour meter at some point to help keep track, too.
I have a pair of Group 24 deep cycle batteries, in two banks. I’d like to at least double my amp capacity. It is not immediately obvious the best way to shoe-horn in more batteries, although I have a couple ideas. A tape measure will be my best friend for awhile. Given the smallish alternator, solar charging will be a good idea.
Boat options:
Air-conditioning! It is probably twenty years old and blows cool, but not cold air. I’m going to see if I can fix this up. As a soon to be live-aboard I believe I will replace this unit if I can’t get it working better (might just need a charge, or perhaps a good cleaning). It does get hot here in the Chesapeake!
Propane on demand hot water heater. It works, and generates scalding hot water. But it seems to take awhile to get going, and the water tanks are small enough that running the faucet while waiting for the hot water to show up seems like a terrible waste of fresh water. Taking a hot shower on a cool morning is pretty damn awesome, though! (Although there are pitfalls to showering aboard). I need to redo the propane lines (it’s a trust issue), so I may decide to get rid of the water heater. It will be kind of odd having a hot water faucet on each of the sinks without any hot water; but such is life. I can use my portable pump up sprayer for showers (it works well) by either solar heating the container or just boiling a pot of water.
Deck wash-down pump. The water around here is muddy. It’s very cool to be able to spray off the chain and deck after raising anchor. Very cool.
Propane stove. I guess the Bayfields came with Origo alcohol stoves; but my 29 has a Kenyon two burner propane job. I’m not a big foodie and I tend to cook simple meals, so this isn’t that big a deal to me. Gas is nice, though. Unfortunately, the stove is not gimballed (and it doesn’t have an oven, although that is of limited interest to me), and there is no easy way to install a permanent gimballed stove without doing major galley surgery and probably sacrificing the starboard quarter berth (which isn’t likely to get used much; but it might be important if it comes time to sell the boat down the road). I have a thought on how to inexpensively build a portable/removable gimballed stove sort of like the old Sea Cook stove, so when the time comes I’m sure I’ll be OK. There is currently a six pound propane tank hanging off the stern pulpit. Before doing any long distance cruising it might make sense to get another.
Conclusion:
While I have a few gripes, I find the boat meets my needs about as well, better really, as could be expected. There are always compromises; but in a sub-thirty foot live-aboard (take away the pulpit, it is probably closer to 27′) I don’t think I could ask for much more. I don’t know if many Bayfield 29s are out doing ocean crossings; but while the design might not be the best choice for a trip around the Horn, I don’t see any reason why she shouldn’t be perfectly capable and comfortable for seasonally appropriate passages providing some modest updating is done; although my experience in the matter is a bit limited.
She makes me smile when I look at her, and even though she looks a little tired at the moment, she gets a lot of compliments. She is thirty years old, and as is reasonably expected, her systems and cosmetics need some attention. Getting old sucks; but I don’t see any reason why “ la Princesa ” (I’m looking forward to the new name) can not be restored to full glory with a modest amount of elbow grease.
Feed from: http://continuousmoon.blogspot.com/
Share this:
- Click to print (Opens in new window)
- Click to share on Facebook (Opens in new window)
- Click to share on Twitter (Opens in new window)
- Click to email a link to a friend (Opens in new window)
- Click to share on LinkedIn (Opens in new window)
- Click to share on Pocket (Opens in new window)
- Click to share on Reddit (Opens in new window)
- Click to share on Pinterest (Opens in new window)
- Click to share on Tumblr (Opens in new window)
4 thoughts on “ Bayfield 29 — An early review ”
I will add some photos to the review above in a day or two. They will help describe some of what I’m talking about.
Any futher comments on your Bayfield? I am considering it for single handing. 63 yo woman sailor here.
My review above pretty much stands, although I’m happy to answer any specific questions you have. I’m still early days in ownership, though.
Single handing, btw, is pretty easy. She’s a stable platform. Docking is a challenge, though. I’m hoping with practice it will get easier.
We have finished year 3 with our 1979 B-29. 6 opening ports, extended bowsprit, wheel steering, no cockpit engine hatch, etc. Docking does get easier- ours pulls hard starboard in reverse but we have a different model Yanmar.
Whatcha thinkin'? Cancel reply
- Sign In or Register
- Boats for Sale
- Research Boats
- Sell a Boat
- Search Alerts
- My Listings
- Account Settings
- Dealer Advertising
- Bayfield 29
Bayfield 29 Boats for sale
1980 Bayfield 29
Green Bay, Wisconsin
Make Bayfield
Category Cutter
Posted 3 Weeks Ago
Discover your next adventure with peace of mind - all details and pictures of this listing have been provided by the seller and our representative has not personally seen the vessel. Unless explicitly noted, the seller assures that all systems are in working order. Our offer process allows plenty of time to personally inspect the vessel to test and verify its condition to provide yourself the assurance you need to buy with confidence! Make a no-risk offer today! Stock #335480 29' Cutter with original sails, One head with holding tank, galley with alcohol stove, fenders, safety equipment, Anchor, cradle! If you're looking for a reliable and well-performing sailboat, then look no further than the Bayfield 29. This 1980 model is a classic and timeless sailboat that has been well-maintained and is ready to take you out on the open water. The Bayfield 29 is constructed out of fiberglass and features a great balance of sail power, form, and stability. Its classic cutter design allows for great performance in both light and heavy winds. With a beam of 10 feet, 2 inches, and a draft of 3 feet, 6 inches, this sailboat is easy to maneuver and has nice balance and agility. The interior of the Bayfield 29 is spacious and comfortable. There are 2 berths with plenty of storage, as well as a galley and spacious head located in the bow. The decks are non-skid, and the side decks give you easy access to the dock. Not only is this a great boat for sailing, but its modern amenities make it perfect for cruising. It is equipped with a depth finder, Marine VHF radio, battery charger, stereo, and more. It also comes with an inboard engine that provides enough power to get you to where you want to go when the winds won't. If you're looking for a reliable classic sailboat that is both powerful and comfortable, then the Bayfield 29 is the perfect boat for you. It's a great option for anyone who wants to enjoy the beauty of the open water and experience the thrill of sailing. Reason for selling is no longer using.
1985 Bayfield 29
Dunedin, Florida
Category Sailboats
Posted Over 1 Month
1985 Bayfield 29 Ted Gozzard design, well cared for pocket cruiser, dependable Yanmar diesel, cutter rig for easy sail handling, spacious teak interior, equipped for coastal cruising.
1986 Bayfield 29 Cutter
North East, Maryland
Model 29 Cutter
Category Cruiser Boats
1986 Bayfield 29 Cutter If you're seeking the perfect sailboat for gunk holing in the Chesapeake Bay, look no further...here she is! With a shallow 3.5' draft, you can find all the nooks and crannies the bay has to offer. She's equipped with a diesel sipping Yanmar so you'll be able to explore far and wide on two to three tanks of fuel all summer...that's barely over $200 in fuel expenses...ALL SUMMER LONG! Designed by renowned designer Ted Gozzard, founder of Bayfield Boat Yard, LTD in southern Ontario, the Bayfield 29 has developed a reputation as a wonderfully handling and very forgiving coastal cruiser. Cutter rigged, she's set-up for single-handling with all lines leading aft to the cockpit, and easily steered from her pedestal steering. She points very nicely and is very forgiving whether under light or heavy winds. Her entry is smooth, and the rounded bottom to the full keel helps reduce pounding, as she slices through the water. Not a fast sailer, but a comfortable, smooth and gentle ride. Her classic lines, from the decorative functional bowsprit to the transom are pleasing to the eye. One look and you'll see why it is no wonder that Bayfield became one of Canada's largest sailboat builders. The interior of the Bayfield 29 is cavernous, with ample headroom, space to relax and move about, and a plethora of storage space. She sleeps four adults comfortably (two in convertible settees and two in aft quarter berths). The fold down dinning table leaves creates plenty of space for passage to the roomy head which is situated all the way forward in the V. The cruising galley is well equipped with a two burner stove, microwave oven and nice deep ice box. She's been well cared for through the years and has cruised the waters of the Chesapeake extensively. Owner is retiring form boating, creating this opportunity. She won't last long, so come see her today!
Cape Coral, Florida
1985 Bayfield 29C
Cortez, Florida
1985 Bayfield 29C Fresh water boat from Lake Michigan. Canadian quality at an affordable price. Comparable to Island Packet and Cape Dory, this Bayfield 29 has a full keel, cutter rig (two head sails), a shallow draft, and a built-in bowsprit (complete with stylized wooden trail boards on either side of its bow). It is an out-and-out cruising boat, and like its smaller counterpart, the Bayfield 25, it starts to come alive when the winds picks up. It features a large anchor locker above deck and anchor rode locker below deck. Heavy duty dual anchor rollers, SS anchor, a 5 foot hanging locker, huge head aft of hanging locker, 6 high quality cast aluminum opening ports, screens for ports and all hatches, single and double berth in main cabin, 2 quarter berths. Lake Michigan boat brought to Florida in 2014. Shows like a 10 year old fresh water boat.
1979 Bayfield 29
Mystic, Connecticut
1979 Bayfield 29 This boat was built in 1979 by the Bayfield Company in Ontario Canada, designed by the world renowned Ted Gozzard. This sea worthy boat features shallow draft for exploring. The roomy cabin and the distinctive large head make the Bayfield very comfortable for both day sailing and week long getaways. She has a 12hp Yanmar which has been yard maintained. Every necessity is already aboard. So, if you are dreaming of sailing away at a sensible price, this yacht is for you! Please "BRING ALL OFFERS!!
Sailboat Brochures from 70's and 80's - mostly Canadian
Grimsby, Ontario
Make C&C
Sailboat brochures from boat shows and dealers in the 70's and 80's, price is for ONE brochure. Here is a list of the others I have. Some have price lists and line drawings. I have noted the year where it shows on the price lists. These are mostly Canadian boat builders that are not in business any more. A great chance to get an original brochure to go with your boat. Send me a note if you have any questions, or if you want me to list one of the other brochures. Abbott 33 Alberg 29 1981 Alberg 37 Aloha 28 Aloha 34 Bayfield 29 1981 Bayfield 32 Bombardier 7.6 C&C 29 C&C 30 C&C 32 C&C 34 1977 CS27 shows sail#1115 CS33 Columbia 8.3 Columbia 9.6 Edel 820 Freedom 28 Freedom 35 Freedom 40 Goman Niagara 26 Goman Express 30 Halman Horizon 27 Halmatic 30 Hinterhoeller Shark 1968 Hinterhoeller 28 1968 HInterhoeller Niagara 30 1968 Hinterhoeller Redwing 30 1968 Hughes Columbia 8.7 1981 Hughes 31 Hughes 35 J24 Luna 24 Niagara 26 Niagara 31 Niagara 35 1977 Nicholson 31 Nordica 29 Nautilus 36 Nonsuch 26 Ontario 28 Ontario 32 Saturna 33 Seawind II 32 Southern Cross 31 Ticon 30 Valiant 32/37/40/47
Narrow Results
Current search reset all.
- Keyword: bayfield 29
- Bayfield (5)
- Cruiser Boats (2)
- Sailboats (1)
- Florida (3)
- Connecticut (1)
- Maryland (1)
- Ontario (1)
- Wisconsin (1)
- POP Yachts (1)
- Search Title Only
- Has Picture
- Include Sold Listings
Showcase Ads
2005 Baja Islander
Cashion Community, TX
1995 Egret 189
Sarasota, FL
2004 Malibu Wakesetter LSV
Columbia, SC
2007 Chaparral 270 Signature
Mill Valley, CA
2016 Bennington 2575 RCW
Huntersville, NC
2011 MB Sports F21 Tomcat
Canyon Lake, CA
2015 Sea Hunt Triton 188
Little Rock, AR
Create Alert
Please, name this search
Select Interval
Alert Successfully Created
Sign up for an account
Already have an account? Log in
Login to continue
Don't have an account yet? Sign Up
Forgot your password?
Log in | Sign Up
- United States
1985 Bayfield 29 | Lilly
Send Message
Description.
I bought Lily in November of 2020. I am the third owner (so i was told). After I completely scraped, sanded and painted the bottom, I've lived on it ever since. My son has moved to Florida to live with me and he's bigger than me and we simply need more room and that's the only reason I'm selling her. Lily is nothing fancy at all, but is a full keel boat and perfect for what I needed at the time to live on. I've added things I ordered on Amazon along the way. If she doesn't sell this season, I'm going to pull the mast and redo all wiring, lighting and standing rigging, some items of which are already on the boat and go with the sale. She's currently in a slip at Harbortown Marina. I pay month to month. You will have to call the office yourself for slip pricing because I will not be a middle man. Serious inquiries only. I accept cash and/or crypto. I have a clear Florida title in hand that is in my name. I have a full survey from February 2021 as a requirement for my insurance provider and will provide only to serious inquirors. No tire kickers, this isn't a mega yacht. The sails and engine are in good condition and everything works as it should for a 37 year old boat.
- Seller zhbaclnr
- Manufacturer Bayfield
- Length 29 ft / 8.84 m
- Beam 11.0 ft / 3.35 m
- Draft 3.5 ft / 1.07 m
- Displacement 7500 lbs / 3401.95 kg
- Condition Good
- Location Florida, United States
- Material: Fiberglass
- Rigging: Cutter
- Hull: Monohull
- Keel: Full Keel
- Sailboat Type: Bluewater
- Covering(s): Bimini Top
- Cabin Layout: Saloon
- Fresh Water: 22 gallons / 83.28 kg
- Holding Tank: 20 gallons / 75.71 kg
- Fuel Capacity: 25 gallons / 94.64 kg
- Engine Make: Yanmar
- Engine Model: 2GM
- Fuel: Diesel
- Fuel Capacity: 25 gallons
- Engine Hours: 1500 hrs
- Horsepower: 20 hp
- Propulsion: Inboard
- Steering: Single Wheel
- # of Cabins: 1
- # of Bathrooms: 1.0
- Bathroom Layout: ?
- Air Conditioning
- Batteries (Marine)
- Battery Charger
- Electric Bilge Pump
- Main Circut Breaker
- Manual Bilge Pump
- Shore Power
- Solar Charger
- Solar Panel(s)
- Wind Generator
- Antifouling
- Flatscreen TV
- Pressurized Water
Rig / Sails
- Head/Jib Sail
- Furlingjib System
- 2 Burner Stove
- Refrigerator
- Swim Ladder
- Fire Extinguishers
- Life Jackets
- Anchor Chain
- Backup Anchor
- Danforth Anchor
- Plow Anchor
Sailboat's Location
Photo gallery.
- --> Seller --> Manufacturer --> Model --> Year --> Length --> Beam --> Draft --> Displacement --> Condition --> --> Location -->