what are the three sails on a sailboat

The Different Types Of Sails And When To Use Them – Complete Guide

Sail forms an integral part of a sailboat. When you sail on the open water and observe other boats (in various sizes), you’d have noticed how each boat type has a specific model of sail. If you’re a beginner in boating, you must know that there are a ton of different sails and they each have their own purpose.

As a general setup, sailboats will use three common sails, including headsail, mainsail, and specialty sail. Due to the varying wind conditions and the model of the sailboat, there are many types of sails including jib, genoa, trysail, storm jib, code zero, gennaker, and spinnaker.

While that sounds like too many models of sails, you can easily differentiate between them and choose the ideal model based on your purpose. This article guides you on this aspect. Let’s begin!

Different Types of Sails & When To Use Them

1. mainsail.

Mainsail is by far the most widely spotted sail model, and it’s usually fixed to the boom and fitted behind the mast. This offers the highest mileage to your sailboat, thereby maximizing speed and performance.

You can use a mainsail if:

You’re concerned about the performance
You need to go faster and utilize all wind power
You need to steer your boat irrespective of the wind’s status
You’ve a large boat and can offer adequate space to this sail.

This mainsail displays a wide surface area to make the most out of the available wind condition. As a result, you can steer your boat quite easily. However, the downside is its size. It is very large and hard to store if you need to take it down for some reason.

Check out my other article all about maintaing sails!

2. Headsail

Similar to a mainsail, it’s very easy to spot a head sail. Just look at the bow of the boat and see if there is a sail. If you see one then yes that’s a headsail. Also called a jib or genoa, a headsail is smaller in size compared to a mainsail and attaches in front of the mast to the forestay. The Foresail will not have a boom for the clew of the sail to attach to. The clew will be attached to the foresails sheet. It can be used without the mainsail in certain conditions but for the most part the two sails are used together. The foresail is always forward of the main.

The headsail comes in many different forms such as a jib, genoa, spinnaker or storm jib. The most common headsail is a jib or genoa.

You can use a headsail if:

Your sailboat is set up for it.
You don’t want to use the mainsail at this time.
Your mainsail is not usable.

The biggest advantage of a headsail is the option to protect yourself even if the wind turns unpredictable or wild. This all depends on the type of headsail you are using.

So, what are the different types of headsails? Let’s take a look!

As more boaters chose to use a headsail for their boats, the jib was introduced as one of its forms. The Jib is a form of headsail that is attached to a shackle present on the deck’s front region.

The Jib is a sail that does not go past the mast when it is raised and in use. If it goes past the mast then you probably have a genoa.

You can use a jib if:

You are out for a normal day of sailing in moderate wind speeds
You have a roller furling. Which is a sail that wraps up around itself.

Some weather conditions can make maneuvering harder or tighter than usual. As a result, it’s essential to use a jib in such cases. It functions well with boats containing a roller furling as the jib handles different positions and tackles the movement of the boat at ease.

2.2 Genoa

Just when you’ve got acquainted with the jib, genoa comes into the picture as a larger version of the jib. If you’re boating along a coastal region, the genoa sail is the one widely used and is attached to the front area of the deck as well.

Here’s a quick trick to find out if a boat has a genoa sail. This genoa is usually larger than a Jib. This means that the genoa effortlessly overlaps and extends itself beyond the mast, thereby covering the mainsail as well.

You should use a genoa sail if:

You’re planning to sail in minimum wind conditions. Less wind means you need more sail.
You find the wind to originate from the rear area.
You own a large boat. Remember that genoa can partially or completely cover the mainsail too. Larger sails for larger boats!

While it’s great for sailing in regular conditions, there are downsides associated with it. A genoa can put you in a dangerous situation if you are sailing in high wind conditions and don’t have the ability to furl in the sail. Furling in the sail will reduce the area of the sail and catch less wind.

Genoas do come in many sizes as well such as 110% or 120%.

The next section of the sail list are ones that aren’t necessary but can be helpful in certain situations. Let’s look at specialty sails!

3. Specialty Sail

While headsails and mainsails are quite commonly used, there are also specialty sails in the market to address specific requirements. Some of the widely seen specialty sails are spinnakers, storm jibs, and code zeros.

3.1 Spinnakers

Spinnaker is a sail dedicated to downwind and is quite large. Think of a beautifully covered parachute.

It’s easy to spot spinnakers as they resemble kites or parachutes. However, it crosses the bow of the boat and isn’t attached to the forestay.

Unlike the genoa sail that covers the mast, a spinnaker fails to do so. The advantage of a spinnaker is the surface area. When the wind is light, the spinnaker can catch a lot more wind giving you more speed. The Spinnaker is usually fixed to three points – pole, halyard, and sheet.

You should use a spinnaker if:

You have minimal wind on a run.
You are trying to harness as much wind power as you can.

While it has a wide surface area, the downside is its inability to steer the boat during strong wind conditions. It can even put the passengers at risk when the wind is at high speeds.

Make sure you have experience before trying out the spinnaker.

3.2 Storm Jibs

Storm jib is another type of specialty sail meant exclusively for rough weather. It’s a tiny, triangular structure that helps during offshore racing or cruising. Just think of it as a smaller jib.

You should use a storm jib if:

You’re going to sail in heavy weather conditions.
You anticipate high wind speeds.
You’re going to be in an offshore race and they are an approved sail type.

Note: In the case of an offshore racing requirement, it’s critical to take prior permission from the regulatory authority for using a storm jib.

3.3 Code Zeros

Code zero is another updated version of a spinnaker that’s meant to be a combination of genoa and gennaker sails. It resembles the look of a genoa but is a lot bigger.

You should use a code zero if:

You’re looking for an overlapping flying headsail.
You’re sailing only in light air conditions.
You’re looking for an alternative to a Genoa.

Having said that, a code zero or a screecher does the job of a genoa with better efficiencies.

3.4 Trysail

Trysail is another type of specialty sail that’s tiny, triangular, and can be fixed right above a gooseneck on the sailboat.

The Trysail is less known in the market as most boaters go ahead with common mainsails and headsails. It’s essential to acknowledge trysail as a front-and-aft mainsail model. It offers excellent performance and contains a permanent pennant in it.

You should use a trysail if:

You’re sailing in heavy weather conditions.
You’re looking for a storm replacement.
You are experienced with using them.

The quadrilateral sail in a trysail is usually turned and bent to a mast, and this helps in heading the vessel during windy conditions.

3.5 Gennakers

If you’ve been able to spot genoa and spinnaker in the past, identifying a gennaker is incredibly easy. A gennaker is a hybrid sail form that is small, slow, and requires no pole attached to the mast.

You should use a gennaker if:

You’re looking for a smaller version of a spinnaker.
You’ve no space to fix a pole to the mast.
You require the sail to be easily manageable.
You’re sailing in a region requiring minimum downwind levels.

Choosing a hybrid sail has a lot of benefits as it combines the usefulness of 2 sail models. However, being aware of their cons is critical to planning a safe sail.

As you begin using these sails, you can also look for better customizations. There are drifters, wind seekers, and other jib types that are meant to handle different wind conditions.

How Many Sails On A Sailboat ?

In general, a sailboat contains two sails. Two sails is the typical setup for the best performance of the boat during different wind conditions. It’s essential to pick your two sails based on your sailing plan.

Why Are There Two Sails On A Sailboat?

A sailboat uses two sails because the wind left over by the first sail is easily caught by the second sail. This helps in steering the sailboat to a better extent and gives the sailboat more power.

Final Thoughts

Sails are one of the major assets of a sailboat. From managing wind to maximizing the performance and longevity of a sailboat, the type of sails you use, plays a huge role. From the various sail types listed in this article, you can choose the best model that fits your sailing routine. Just make sure to remember to check and make sure they are the correct size for your vessel.

Make sure to plan ahead and have the right sails for your sailing weekend. Cheers!

Boatlifehq owner and author/editor of this article.

The Most Popular Types Of Sails On A Sailboat

A sloop-rigged sailboat typically features a mainsail, a headsail, and an additional light-wind sail, such as a spinnaker or Gennaker. The mainsail is rigged aft of the mast, while the headsail is attached to the forestay. The two most commonly used headsails are the Genoa and Jib.

The sails are vital parts of a sailboat since you obviously couldn’t sail without them! There are many different sails depending on the type of sailboat and its rig configuration, and we’ll walk through them together in this article.

The different types of sails on a sailboat

We can divide the selection of sails on a sailboat into three categories:

Standard sails

Light-wind sails

Storm sails

Each category serves different purposes depending on the vessel’s rig configuration and the sail’s functionality.

The standard sails

The standard sails usually form a sailboat’s basic sail plan and include :

The Mainsail
The Staysail
The Mizzen sail

These sails are the ones that are used most frequently on sloop, ketch, and cutter-rigged sailboats and are usually set up to be ready to use quickly.

Headsails are often rolled up on a furler, while the main and mizzen sail are stored on the boom or furled into the mast.

The halyards and sheets are kept within easy reach, making these sails the primary choice in most situations. Let’s dive further into each of them.

The mainsail is a triangular sail that flies behind the mast on top of the boom . Although it may not always be the largest sail on the vessel, we commonly refer to it as “the main.”

It is a vital sail, and keeping the sail shape trimmed properly on every point of sail is crucial for the stability and performance of the boat.

A Jib sail is a headsail that does not overlap the mainsail. It is typically between 100% and 115% of the foretriangle but can also be smaller. The foretriangle is the triangular area formed by the mast, deck, and forestay. The Jib is often used with a self-tacking system involving a sheet traveler in front of the mast.

This sail is often seen on newer boats with fractional rigs, which typically have a larger mainsail area than the headsail area. However, the Jib is versatile and also used in other configurations.

People often mix the terms Genoa and Jib. Many refer to any headsail as a Jib, which is incorrect. I personally prefer to use the correct terms to avoid confusion .

A Genoa sail resembles a large Jib but extends past the mast and overlaps the mainsail. Genoas are usually larger than 115% of the foretriangle , with sizes ranging from 120% to 150%. They are often used on vessels with masthead rigs and smaller mainsails but are also common on fractional rigs.

The Staysail is typically found on cutter rigs and is set on the inner forestay or cutter stay. It can be combined with other sails, such as a Jib, Genoa, or Yankee, or on its own in stronger winds.

The Staysail is also useful when sailing downwind, as it can be paired with a headsail and extended to opposite sides of the boat using a pole.

The Yankee sail resembles a Genoa and Jib but has a high-cut clew. This shape allows for improved airflow when used with another headsail. The Yankee is often used on cutter-rigged boats in combination with a staysail and is known for its versatility in different wind conditions.

Mizzen Sail

A mizzen sail is similar to the mainsail, only smaller . It is set on the aft mast of a boat with multiple masts, such as a ketch rig. The mizzen sail is usually used to provide balance and stability to the vessel and provides additional power when sailing downwind.

Another handy usage is to fly the mizzen at anchor to keep the bow up against waves and swell.

The light-wind sails are large, made of thin nylon, and typically shaped like a half-balloon. They are a type of headsails that are great when the winds are too light to fill the standard headsail and are often used when sailing downwind.

The four most commonly used light-wind sails are:

The Spinnaker
The Gennaker
The Code Zero
The Parasailor

They all provide excellent forward propulsion on a sailboat but usually require some extra rigging to be set.

Experienced cruisers love to use light-wind sails in nice weather, but they have a critical weakness to be aware of. These sails easily get overpowered when the wind increases, and I strongly advise being careful and observant of the wind conditions when flying them.

(Yes, I have managed to rip mine on one occasion due to getting overpowered, but that’s a different story…)

Let’s continue and take a closer look at each of the light wind sails.

A Spinnaker sail is a large, lightweight downwind sail used at deep angles between 120 and 180 degrees. It is symmetrical in shape with two clews and is often brightly colored.

The Spinnaker is set by using a pole to extend the sail’s clew to the vessel’s side. Then, a sheet is attached to the other clew and led back to the stern of the boat.

A Gennaker sail combines the characteristics of the Genoa and Spinnaker. It is made of nylon like the Spinnaker but is asymmetrical like a Genoa and rigged slightly differently. The tack is attached to the bow, and the clew has a sheet led aft to the cockpit. The Gennaker can be equipped with a snuffer to make it even easier to set up and take down.

It is popular among cruisers because it is simpler to use than a spinnaker and it doesn’t require a pole. The sail is effective at angles between 90 degrees and almost all the way down to 180 degrees, making it versatile for various light-wind conditions.

A Parasailor is similar to the Spinnaker in many aspects but has some distinct differences. It has a double-layer wing that inflates as the sail is filled with air, creating a batten-like effect pushing the leech out while providing lift to the bow.

The wing also helps to prevent the rolling movements you get with a Spinnaker and the collapsing of the leech that can occur with a Gennaker at deep angles.

This makes the parasailor effective at sailing angles between 70 and 180 degrees dead downwind. Parasailors can be set like a Gennaker when reaching or with a pole like the Spinnaker for running downwind.

A Code Zero sail combines some elements of the Genoa and Gennaker. Unlike the Gennaker, the Code Zero has a different shape, allowing it to be used while sailing upwind.

Another benefit is that it can be used with a furler which makes it easy to roll in and out. However, it can’t replace the Gennaker or Spinnaker entirely, as it is not effective at sailing angles deeper than 120 degrees.

If you see a big yacht with three forestay’s, the forward one probably holds a code zero sail. A bow spirit allows the ability to fly additional light wind sails as well!

Storm Sails

The storm sails consist of a small Mainsail and Jib in heavy-duty materials designed for rough conditions. These sails enable us to maintain speed and stability in the boat in severe weather too strong for the standard sails.

Storm sails are often brightly colored , such as red, orange, or yellow, to make them more visible at sea.

Storm Mainsail

A storm mainsail is used when the reefing setup doesn’t allow the standard mainsail area to be reduced enough to prevent overpowering. The sail can handle rough conditions and is excellent for maintaining stability.

A storm Jib is used when the headsail has been furled to the point where it is no longer effective. It is especially useful for sailboats rigged with a Genoa, as the Genoa gets inefficient when heavily reefed. As the storm Jib is smaller than the standard headsail, it also lowers the center of gravity, making the vessel heel less and become more stable.

Explaining the terms for the parts of a sail

Let us talk some more about sails. The goal is to go sailing, right?

Identifying the different parts of the sails is crucial to understanding which lines go where.

Let’s zoom in on a sail and break down the terms :

The head is the top corner of the sail . Most mainsails have a headboard or plate where the halyard is connected, while headsails use a metal ring. A halyard is a line we use to raise and lower sails with.

The leech is the aft part of a sail , located between the clew and head. We use a combination of the outhaul, main sheet, and traveler to trim and adjust the leech on the mainsail.

The headsail’s leech is trimmed by adjusting sheet tension and angle according to the wind speed and direction. A traveler is a track with a movable car or pulley system for adjusting the position and angle of a sheet, and most sailboats have one main traveler for the mainsail and car tracks along the side decks for the headsail.

The luff of a sail is the front part of the sail between the tack and head. On a mainsail, the luff runs vertically along the mast and along or close to the forestay on a headsail. Headsails are often equipped with luff foam to help maintain their shape when partially reefed on a furler.

Battens are slats or tubes inserted into pockets on the mainsail to help the sail maintain its shape and increase its lifespan . A traditional sail hoisted and lowered on the boom typically has horizontal battens. Vessels with in-mast furling can use vertical battens instead of horizontal ones.

A fully battened Mainsail has the battens run through the entire sail length from the luff to the leech.
A standard battened main sail has the battens along the sail’s leech.

Telltales are small ropes, bands, or flags attached to a sail to give an indication of the airflow around the sail. They help us understand how the wind affects the sail and allow us to fine-tune the trim for optimal performance. Telltales are usually found on the mainsail’s leech and in the front of the headsail’s leech.

The clew of a sail is the lower aft corner and where the outhaul is connected on a mainsail. Headsails have sheets attached to their clew for controlling and trimming the shape and tension.

The tack is the lower, forward corner of a sail. On a traditional Mainsail, the tack is attached to the Gooseneck, a hinge in front of the boom attached to the mast.

With in-mast furling, the tack is connected to the furling mechanism. This mechanism is used to roll the sail into the mast.

The headsails tack is connected to a furler drum on the forestay on most sailboats. Vessels using traditional hank-on headsails connect the tack to a fixed point on the bow.

The foot of the mainsail is the bottom portion of the sail between the clew and the tack. It is trimmed using the outhaul, a line attached to the clew, and used to adjust the tension on the foot of the sail. Some mainsail are configured loose-footed, and others are attach-footed.

The foot of the headsail is trimmed by adjusting the tension and angle of the sheets, which are the lines used to control the headsail’s clew. We use cars, or pulleys, to adjust the angle of the sheets and thus the trim of the headsail.

Traditional and less commonly seen sails

We’ve now looked at the most commonly used sails and walked through the different parts of them. But what about the less common ones? The art of sailing has a rich history, with some unique sail designs that we rarely see today.

Read on if you want to peek into some traditional sails, or skip straight to popular sail and mast configurations here.

Square sails

Square sails are rectangular and usually set across a ship’s mast, mostly seen on traditional square-rigged sailing ships and Viking ships. These sails are efficient for downwind sailing and are hung from horizontal spars called yards. Though not as agile as modern fore-and-aft sails when sailing upwind, they were central to naval exploration for centuries. Today, they’re mainly seen on traditional vessels and tall ships, symbolizing maritime heritage.

If you’ve been to Martinique in the summer, you may also have noticed the round skiff sailboats the local fishermen traditionally used for fishing in the Atlantic Ocean with their distinctive big squared sails. Tour de Martinique des Yoles Rondes is a popular yearly event where the locals race and show off these beautiful old boats with colorful sails!

A gaff sail is a traditional four-sided sail held up by a horizontal spar called the “gaff.” They are used on classic gaff-rigged sailboats and allow for a larger sail area with a shorter mast. Gaff-rigged boats were traditionally popular and usually carried 25% more sail area than the equivalent Bermudan rig, making them fast on a downwind run. The Gaff rig could also carry a topsail between the gaff and the mast.

However, they don’t sail well to windward, and modern designs have shifted towards triangular sails for better upwind performance.

Jib-headed topsail

The Jib-headed topsail is a small triangular sail used on gaff rigs and is set between the gaff and the top of the mast.

A lug sail is an angled, four-sided sail that attaches at a point on its top side, making it hang tilted. The sail is simple to use and often found on smaller or older boats. There are different types, like standing, dipping, and balance lugs, each hanging differently around the mast.

The lug sail evolved from the square sail to improve how close the vessels could sail into the wind. Because of their upwind performance, fishermen used them widely in Europe from the seventeenth through the nineteenth centuries.

Sprit sails

The spritsail, with its unique four-sided design, stands out thanks to a diagonal support called the “sprit.” It was traditionally popular in Thames sailing barges due to its ability to accommodate high-deck cargo. These days, it’s primarily found in smaller boats like the Optimist dinghy in a variant called “leg of mutton spritsail.”

The spritsail was also used in traditional wooden boats like the fearing version of the Oselvar wooden boat traditionally used in western Norway.

It is also commonly used by the indigenous Guna Yala tribes in Panama in their dugout Ulu’s up to this day. We saw plenty of them when we cruised along the coast, and some of them approached us to sell us their delicious catch of the day!

Lateen sails

A lateen sail is a triangular sail set on a long spar angled on the mast. It was originally popular in the Mediterranean and on Arab shows, and its design enhanced maneuverability and played a crucial role in historic sea exploration.

The lateen sail was used on lateen rigs, the predecessor to the Bermuda rig – one of today’s most commonly used rigs!

Which brings us to the following topic:

Popular sail and mast configurations

There are many different rigs and sail configurations between sailing vessels. From the old-school square rigs to schooners, gaff rigs, and more. However, this article will focus on the three most popular rigs seen on modern sailboats:

The Bermuda Sloop Rig
The Cutter Rig
The Ketch Rig

The three rigs have similarities and differences between their sail and mast configurations. We’ll walk through each of them to understand how they utilize their different types of sail.

If you want to learn more about other rigs, take a look here .

Bermuda Sloop Rig

The Bermuda sloop rig is the most common rig on modern vessels. It is characterized by a single mast, a triangular mainsail, and a headsail. This rig is named after the Bermuda Islands, where it was developed in the 17th century.

Some of the key features of the Bermuda sloop rig:

The mast is typically tall and raked, which allows for a large sail area and excellent stabilit y.
The mainsail is attached to the mast and boom. It is usually combined with a single headsail at the front of the boat, making it powerful and easy to sail.
The Sloop is usually equipped with a masthead or fractional rig and flies a Jib or Genoa as its primary headsail.

The Bermuda Sloop rig is known for its simplicity, is often used for racing and cruising, and is popular among sailors worldwide.

The cutter rig is very similar to the sloop rig. The significant difference is that it has a single mast and two headsails – a Staysail and a Yankee. The cutter rig is known for its versatility due to the multiple options in sail plans and the double headsail setup.

Some key aspects that separate the Cutter from the Sloop:

The rig is often more robust than its Sloop sister because of the additional cutter stay and running backstays.
The mast is located closer to the center of the boat.
The Cutter has a staysail on the inner forestay and a Yankee sail on the outer. The sails can be used in combination with each other or independently.
Tacking the headsail between the forestay and cutter stay is more involved than on a sloop.
The Cutter rig has two similar variations: the Slutter rig and the Solent rig.

Like the Sloop, the Cutter rig is relatively easy to operate. Still, the additional headsail and rigging make it costlier to maintain. It is also less suitable for racing than the Sloop, but the added versatility helps in different weather conditions and makes it an excellent choice for cruisers.

The ketch rig is also similar to the Sloop but has an additional mizzen mast placed further aft of the main mast. Another mast gives it the advantage of even higher versatility in sail plans. The ketch typically uses three sails. The mizzen sail, a mainsail, and a headsail. The mizzen mast also allows it to fly a second light-wind sail.

Here are a few more distinctions of the ketch rig:

The ketch typically carries a smaller mainsail than a similarly sized sloop and a smaller mizzen sail.
A small mizzen and a medium mainsail are easier to handle than one large mainsail.
The additional mizzen sail makes the vessel easy to balance and gives extra stability downwind.
The ketch usually doesn’t point as close to the wind as the Sloop and Cutter.

The headsail setup on a ketch is generally the same as for the Sloop. But the ketch can also be rigged as a cutter ketch, which gives it the benefits of the cutter rig! The tradeoff with a cutter-rigged ketch is the higher complexity and additional rigging, hardware, and sails required.

Final words

Well done, you now have a good grasp of the most common sails and their strengths. We have discussed a few rigs and how they utilize different kinds of sails in various sail plans. Remember that more sail types, other rigs, and even more variations are available. It is a complex topic, but this guide covers the basics and gives you a great starting point.

If you still have questions, look below at the FAQ, or leave me a comment. I’m more than happy to help you out!

A sailboat is only as good as its sails, and sails need wind to work. The next logical step is learning how the wind works when we sail and practicing some wind awareness! Head to the following guide to continue your research: Learn The Difference Between True And Apparent Wind Speed.

FAQ: The Different Types of Sails On A Sailboat

What is the foretriangle on a sailboat.

The foretriangle on a sailboat refers to the triangular area formed between the mast, forestay, and deck. If you want to order a new headsail, for example, you’ll have to measure and supply the sailmaker with these details.

What is the difference between a loose-footed and attached-footed mainsail?

A loose-footed mainsail is attached to the boom only at its corners, leaving the rest of the sail’s bottom edge free. An attached-footed mainsail, on the other hand, is secured to the boom along its entire length. The main difference lies in how the bottom of the sail connects to the boom, with the loose-footed design offering more adjustability in the sail shape.

What is a high-cut clew on a sail?

A high-cut clew refers to the design of a foresail, such as a jib or genoa, where the back lower corner (the clew) is raised or “cut” higher above the deck compared to standard designs. This design allows for better visibility beneath the sail and makes it easier to sail over waves without the sail touching the water, which is especially beneficial for offshore or blue-water cruising. Very high-cut clews are commonly seen on yankee sails on cutter-rigged sailboats.

What is luff foam on a sail?

Luff foam is a padded strip sewn into the forward edge of roller furling sails. It ensures the sail is appropriately shaped when partially rolled up, especially in strong winds. This foam not only helps with sail performance but also protects the sail when it’s furled.

What are the most common sails?

The sloop rig sailboat is the most common and usually features a mainsail, a headsail, and an additional light-wind sail, such as a spinnaker or Gennaker.

What are the different types of sails?

There are several different types of sails, and we can divide the most common into three categories:

The standard sails:

Mizzen sail

The light-wind sails

The storm sails:

Storm mainsail
Storm jib

What is a spinnaker sail?

A Spinnaker sail is a large, lightweight downwind sail used at deep angles between 120 and 180 degrees.

What is a Jib sail?

A Jib sail is a headsail that does not overlap the mainsail and is set on the forestay. The Jib can also be set up with a self-tacking system, making it very effective when sailing into the wind.

Is Genoa sail the same as a jib?

People often mix the terms Genoa and Jib. The Genoa is different from a Jib sail as it is larger and overlaps the mainsail, whereas the Jib is smaller and does not overlap the mainsail.

What is a Genoa sail?

A Genoa is a headsail larger than the Jib extending past the mast and overlapping the mainsail. The advantage over the Jib is the larger sail area, making it more effective when sailing off the wind.

How many types of sail plans are there?

Sail plans refer to the configuration and arrangement of sails on a boat or ship. While there are countless customizations and variations, the three most common sail plans are:

Sloop: Characterized by a single mast, a triangular mainsail, and a headsail.

Cutter: Similar to a sloop but has a single mast and carries two or more headsails.

Ketch: Features two masts, with the aft mast (called the mizzen) shorter than the main mast.

What is a Mainsail?

The mainsail is a triangular sail that flies behind the mast on top of the boom.

What is a Gennaker?

A gennaker is basically an asymmetrical spinnaker. A hybrid sail that combines the characteristics of a Genoa and a Spinnaker, designed for sailing off the wind and often used in light to moderate wind conditions.

What is a Storm Jib?

A storm jib is a small, heavy-duty sail used in strong winds or stormy conditions. It is commonly used when the headsail has been furled to the point where it is no longer effective.

What factors determine the type of sail to be used?

The type of sail to be used depends on various factors such as wind conditions, points of sail, sailboat size , and sailing experience. It’s smart to choose the appropriate sail for optimal performance. A Jib, for example, will be more effective than a Genoa while sailing to windward, and vice versa.

How do sails affect the performance of a sailboat?

Sails are the engine of a sailboat. Their design, size, and trim influence the boat’s speed, direction, and stability. Properly adjusted sails capture wind efficiently, allowing the boat to move faster and in the desired direction.

The balance and condition of the sails also impact comfort and safety, with well-maintained sails ensuring optimal performance. The sails are essential in determining how a sailboat performs in various wind conditions.

Sharing is caring!

Skipper, Electrician and ROV Pilot

Robin is the founder and owner of Sailing Ellidah and has been living on his sailboat since 2019. He is currently on a journey to sail around the world and is passionate about writing his story and helpful content to inspire others who share his interest in sailing.

Your article gave me a lot of inspiration, I hope you can explain your point of view in more detail, because I have some doubts, thank you.

What specifically do you want my point of view on?

Sail Types: A Comprehensive Guide to 8 Types of Sails

Sailboats come in all shapes and sizes. And that means there are many types of sails on the market! For those who might not know, sails are made of canvas and use wind power to propel sailboats through the water.

Understandably, different sails are required for different types of sailboats . And sailboats are categorized by the number of hulls they have. Monohulls have a single-hull design, catamarans have two hulls, and trimarans have three. Generally, sailors use catamarans for upwind sailing (but they can be used to sail downwind in certain conditions).

The type of sail you'll need for your sailboat depends on the kind of sailboat you have. Additionally, sails are highly dependent on the wind and weather conditions. Therefore, it's always a good idea to have different types of sails on board to navigate the ever-changing weather conditions.

8 Types of Sails for Sailboats

As mentioned, you should carry multiple sails when sailing to prepare for various weather conditions. Here's a brief overview of the types of sails for sailboats:

1. Mainsails

The mainsail is the largest and most important sail. Therefore, it's probably the first sail to come to mind when you think of camping. Typically, it's situated directly behind the mast — connected to the boom — and uses wind energy to move the vessel. The mainsail plays a significant role in tacking and gybing, making it essential for any voyage.

Since the mainsail is a larger sail, it doesn't require wind to propel it forward. And the fact that it can be moved by moving the boom makes it uber-easy to operate.

Learn More About Sailing

2. Headsail

The headsail often accompanies the mainsail, though it is smaller in size. Regardless of your sailboat type, the headsail is positioned at the front of the mast – over the sailboat's bow.

Because headsails are small, they are helpful when navigating through windy conditions. Smaller sails catch less wind, preventing them from propelling your boat as strongly as larger sails. Additionally, headsails help lift, balance, and protect the vessel from inclement weather conditions.

While the term 'headsail' refers to any sail in front of the mast, the jib is the most common type of headsail. (And when a jib is so large that it overlaps the mast, it's called a genoa.)

Learn More About Sailboats

3. Genoa

The genoa is a large sail that attaches to the front of the forestay. (In this instance, it's similar to a headsail.) However, the genoa is larger than the headsail and overlaps the mainsail partially or completely to help the boat go faster.

Genoa sails are useful when sailing through light or medium wind. You can also use it when the wind comes directly from the rear. If you use a Genoa sail during high winds, you'll probably start sailing too quickly and put yourself and your boat at risk.

4. Spinnaker

The spinnaker is a large and whimsical (often colorful) sail. Spinnaker sails are usually symmetrical, allowing them to reach different points of sail. Generally, these are lighter sails and don't cover the mast like the genoa.

Because spinnaker sails are on the larger side, you have to be incredibly careful with them. Don't use them in rough conditions. Instead, save them for sailing in low winds and calm seas.

5. Gennaker

As the name suggests, the Gennaker sail combines a spinnaker and a Genoa sail. They are as large as the spinnaker, although they're not symmetrical.

They come in handy whenever the wind changes from a pure dead run to a reaching point of sail, as sailors can navigate various wind types with the same sail. It's still only meant for lighter and milder winds, but it's more versatile than the spinnaker and genoa.

6. Light Air Sails

Light air sails are useful in calmer conditions when the headsail and mainsail alone aren't cutting it. They include:

Code Zero : A code zero sail is a gennaker sail ideal for sailing in light to mild winds. It's designed to create lift and boost boat speed whenever regular sails don't generate enough power. For that reason, many racers and cruisers use code zero sails to improve performance and gain control in various situations.
Windseeker : This small, special sail is reserved for no wind or light wind. Essentially, it helps boats remain maneuverable in extremely calm conditions. And for that reason, it's valuable to long-distance sailors.

7. Storm Jib

Storm jibs can be used as a headsail whenever the weather is particularly rough and windy. Because it functions as a safety seal, it prevents boats from capsizing by reducing the sail area exposed to the wind. Therefore, it's a necessary sail for every sailor.

Join Our Newsletter!

Get community news, buying bargains, and how-to guides at your fingertips.

Most Popular Types of Sails on a Sailboat

Learning about how there were different types of sails on sailboats for me was a bit strange at first. I thought something along the lines of “Don’t you just need to put some fabric on some polls and grab the wind?” Obviously, there’s far more to it than that.

So what are the most popular types of sails on sailboats? The mainsail, headsail (or jib), genoa, spinnaker, and gennaker are the most popular types of sails on sailboats. There are also a number of different configurations when considering the type of sail and mast in use including a sloop, fractional rig sloop, cutter, ketch, schooner, yawl, and cat.

Simply put, different sailboat sails serve different purposes when out on the water.

The sail is kind of like the “engine” of your sailboat (of course, sailboats can have actual engines) in that it’s the main source of forward propulsion.

So, it’s important to know when best to use either type of sail and why including the many different names of sails on a ship.

Types of Sails

There are a number of reasons why you’d want to use one sail over another, but the most important points to consider have to do with the point of sail you’re sailing in and the wind strength.

Maybe you need downwind sails, square sails, or a triangular sail. Maybe a unique sail shape, sail cloth, or sail area. With that in mind, let’s check out the different sail types!

The mainsail is by far the most popular type of sail on sailboats and is often the first image that comes to mind when thinking about a sailboat.

Mainsails are found behind the mast and attached to the boom, which makes it a common part of the sailboat to keep an eye on as it takes up a lot of real estate on a boat with sails especially during a sail tack.

Mainsails are able to cover a lot of surface area with respect to incoming winds, especially since they’re attached to the boom.

The fact that they have a large surface area means they don’t require very strong winds to provide good forward propulsion on a sailboat.

Also, since the position of the mainsail can be easily configured thanks to the boom, all points of sail are achievable.

Headsail/Jib

The headsail (or jib) is probably the second most popular type of sail on sailboats since it usually accompanies the mainsail.

The headsail is always placed at the front of the mast and can cover a good amount of the bow of the sailboat. It’s also smaller than a mainsail, making it more portable and easy to work with.

Headsails aren’t as big as mainsails, therefore they have a smaller surface area which results in the fact that they’re not capable of catching as much wind as a mainsail.

This is an important point though since if the current wind is exceptionally strong and your mainsail has been trimmed as much as possible, being able to put away your mainsail and depend on your headsail alone is an excellent strategy to reduce speed.

When the wind is just too strong to keep your mainsail out, putting it away and using only your headsail is a great option.

You won’t be grabbing as much wind as with the mainsail and you’ll be able to have a much more enjoyable (and safer!) sailing experience.

One of the most picturesque sailing images one can conjure up is the one with a sailboat using a genoa sail (see the image above on the right).

A genoa is a type of large jib that’s attached to the front of the forestay just like a headsail.

One of the main differences with the genoa sail is that it’s bigger than the normal headsail and oftentimes extends behind the mast partially or completely covering the mainsail. It actually used to be called an “overlapping jib”.

Using a genoa sail means you have light to medium winds and your sailboat is more or less in a dead run point of sail (wind coming directly from the rear or sailing downwind).

Since the surface area of a genoa sail is so large, it’s important only to use it when winds are relatively low. Otherwise, you’ll be moving exceptionally fast resulting in a potentially risky situation.

A spinnaker sail is a fun sail to use since it’s quite large, colorful, and can pick up a lot of wind.

Unlike a genoa sail, they’re often symmetrical making them more sensitive to the reaching points of sail and thus more appropriate for the running point of sail. They’re also lighter and have a “kite” kind of feel to them.

The reason they resemble a “kite” is not only that they’re generally lighter and more colorful than other types of jibs, but also they don’t cover the mast like a genoa sail.

Instead, they don’t attach to the forestay and stretch out toward and past the bow of a sailboat. Since they’re bigger than genoa sails, you want to be even more careful to only use them in relatively low and non-volatile wind environments.

A gennaker sail is a more recent type of sail on sailboats since they were developed around 1990.

Gennakers are a cross between genoa and spinnaker sails (as the name might suggest), which are big like a spinnaker, aren’t as symmetric as a spinnaker, and aren’t attached to the forestay like a genoa sail or headsail.

The reason for the invention of the gennaker is that sailors wanted to take advantage of lighter winds without having to resort to using a spinnaker if the winds change from a pure dead run to more of a reaching point of sail.

All in all, the gennaker sail is able to bridge the performance gap between a genoa and spinnaker sail in terms of being able to take on a more flexible point of sail while taking advantage of relatively softer winds.

Popular Sail and Mast Configurations

Now that you’re familiar with the most popular types of sails on a sailboat, it’s good to get an idea of how these sail types relate to the configuration of a sailboat’s mast.

There are a huge number of combinations when it comes to sails and mast configurations, so I thought I’d lay out the most popular ones you’ll likely run into out on the water.

A sloop is the most common type of sail and mast configuration for sailboats. The sloop is the classic single mast, double sail setup.

The sails on a sloop consist of a mainsail and a headsail. The headsail can be different types of jibs, including the genoa, spinnaker, or gennaker sails. The headsail is connected to the forestay on the mast and runs all the way to the top of the mast.

Fractional Rig Sloop

Similar to a sloop, a fractional rig sloop has a single mast, double sail setup. The only difference, however, is that the forestay doesn’t reach the top of the mast, resulting in the headsail being restricted to a fractional amount of space a normal sloop would allow for.

This reduction of surface area for the headsail means that less wind can be captured and, thus, reduced sailboat speed.

A cutter is an interesting setup since it’s just like the sloop and fractional rig sloop setup, but instead of one forestay it has two. With two forestays on the mast, cutters are able to house two headsails.

This can be a preferred setup because it allows for easy cruising due to it offering a diverse combination of points of sail for different strengths of wind.

A ketch is a less common setup when compared to the previous setups since it has two masts.

Just like a sloop, it has a mast that allows for a mainsail and headsail with a full range forestay, but it also has a smaller sized mast between the mainmast and the stern of the sailboat.

This mast configuration was commonly used in Northern European freighter and fishing boats and is called the mizzen mast.

If you’ve ever seen Pirates of the Carribean, you’ll have seen almost nothing but schooners. A schooner is when a sailboat has two or more masts, similar to a ketch, while having a number of sails to manage.

The main differences between a ketch and a schooner are that a schooner’s aft mast (the rear mast) is taller than the forward mast and a schooner can have up to six masts some including a square sail or two. This makes names of sails on a schooner the fore and aft sail (or fore and aft rig).

A yawl is almost identical to a ketch with the only difference being that the mizzen mast is located directly behind the sailboat’s rudder post. In terms of a ketch vs yawl, the mizzen sail is also much smaller than the mizzen sail on a ketch due to its position on the sailboat.

A cat has one mast and one sail with the mast being positioned at the bow of the sailboat. This mast configuration is most commonly found on smaller sailboats, especially dingy sailboats. These types of sailboats are colloquially called “catboats”.

Get the very best sailing stuff straight to your inbox

Nomadic sailing.

At Nomadic Sailing, we're all about helping the community learn all there is to know about sailing. From learning how to sail to popular and lesser-known destinations to essential sailing gear and more.

Quick Links

Business address.

1200 Fourth Street #1141 Key West, FL 33040 United States

Copyright © 2024 Nomadic Sailing. All rights reserved. Nomadic Sailing is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means to earn fees by linking to Amazon.com and affiliated sites.

The different types of sails and their uses

Discover the different types of sails and their uses to optimize your sailing performance and enjoy the freedom and fulfillment of exploring the open sea.

The Different Types of Sails and Their Uses

Sailing is an incredible way to explore the world, spend quality time with family, and embrace the freedom of the open sea. As you embark on your sailing adventure, it’s essential to understand the different types of sails and their uses. This comprehensive guide will provide you with the knowledge you need to navigate your journey confidently.

Introduction to sails, symmetrical spinnakers, asymmetrical spinnakers, sail materials and construction.

Sails are the driving force behind any sailing vessel, harnessing the power of the wind to propel the boat forward. They come in various shapes, sizes, and materials, each designed for specific sailing conditions and purposes. Understanding the different types of sails and their uses will help you make informed decisions when selecting sails for your boat and optimizing your sailing performance.

The mainsail is the primary sail on a sailing vessel and is typically hoisted on the aft side of the mast. It is a triangular sail with its leading edge (or luff) attached to the mast and its foot running along the boom. Mainsails are essential for providing the boat with forward propulsion and play a significant role in steering and balancing the vessel.

There are two primary types of mainsails: full-batten and partial-batten. Full-batten mainsails have horizontal battens that run the entire width of the sail, providing additional support and shape. Partial-batten mainsails have shorter battens that only extend partway across the sail. Full-batten mainsails tend to hold their shape better and last longer, while partial-batten mainsails are lighter and easier to handle.

Headsails are sails that are set forward of the mast and are used in conjunction with the mainsail to provide additional propulsion and balance. There are several types of headsails, each with its unique characteristics and uses.

A jib is a triangular sail that is set forward of the mast and is attached to the forestay, a wire that runs from the masthead to the bow of the boat. Jibs come in various sizes, with smaller jibs being more suitable for strong winds and larger jibs providing more power in light wind conditions. Jibs are essential for upwind sailing, as they help to direct the airflow around the mainsail, increasing its efficiency.

A genoa is a type of jib that is larger than a standard jib, extending past the mast and overlapping the mainsail. Genoas are designed to provide maximum sail area and power in light to moderate wind conditions. They are particularly useful for upwind sailing, as their large size helps to generate more lift and drive the boat forward. However, genoas can be more challenging to handle than smaller jibs, especially in strong winds or when tacking.

Spinnakers are large, lightweight sails designed for downwind sailing. They are typically set forward of the jib and are not attached to the forestay. Instead, they are held out by a pole called a spinnaker pole, which is attached to the mast and the sail’s clew (the lower aft corner of the sail). Spinnakers are used to catch the wind from behind, providing significant power and speed when sailing downwind.

A gennaker, also known as a cruising spinnaker or code zero, is a hybrid sail that combines the characteristics of a genoa and a spinnaker. Gennakers are designed for reaching and downwind sailing and are typically set on a furling system, making them easier to handle than traditional spinnakers. They provide more power than a genoa in light wind conditions and are more stable and easier to control than a spinnaker.

Downwind Sails

Downwind sails are designed specifically for sailing with the wind coming from behind the boat. These sails are typically larger and lighter than upwind sails, allowing them to catch more wind and generate more power. There are two main types of downwind sails: symmetrical spinnakers and asymmetrical spinnakers.

Symmetrical spinnakers are large, balloon-shaped sails that are designed for sailing directly downwind. They are symmetrical in shape, with the sail’s centerline running vertically down the middle of the sail. Symmetrical spinnakers are held out by a spinnaker pole, which is attached to the mast and the sail’s clew. This allows the sail to catch the wind from behind, providing maximum power and speed when sailing downwind.

Asymmetrical spinnakers, also known as gennakers or A-sails, are designed for reaching and downwind sailing at angles that are not directly downwind. They are asymmetrical in shape, with a longer luff (leading edge) and a shorter leech (trailing edge). Asymmetrical spinnakers are typically set on a furling system and do not require a spinnaker pole, making them easier to handle than symmetrical spinnakers. They provide more power and stability than a genoa in light wind conditions and are more versatile than a symmetrical spinnaker.

Storm Sails

Storm sails are small, heavy-duty sails designed for use in extreme weather conditions. They are used to replace the standard sails when the wind is too strong, providing better control and reducing the risk of damage to the boat and its rigging. There are two main types of storm sails: storm jibs and trysails.

A storm jib is a small, heavy-duty jib that is used in place of the standard jib in strong winds. It is typically set on the inner forestay, closer to the mast, providing better balance and control. Storm jibs are designed to withstand high wind loads and are made from durable materials, such as heavy-duty Dacron or laminate fabrics.

A trysail, also known as a storm trysail or storm mainsail, is a small, heavy-duty sail that is used in place of the standard mainsail in extreme weather conditions. It is typically set on a separate track on the mast, allowing it to be hoisted independently of the mainsail. Trysails are designed to provide better control and balance in strong winds and are made from durable materials, such as heavy-duty Dacron or laminate fabrics.

Sails are made from various materials, each with its unique characteristics and performance attributes. The most common sail materials include Dacron, laminate fabrics, and high-performance fibers, such as carbon and aramid.

Dacron is a durable, low-stretch polyester fabric that is widely used for cruising sails. It is relatively inexpensive and provides good performance in a wide range of conditions. Laminate fabrics are made by sandwiching layers of polyester or high-performance fibers between layers of Mylar film. These sails are lighter and more resistant to stretch than Dacron sails, providing better performance and shape retention. High-performance fibers, such as carbon and aramid, are used in racing sails and offer the highest levels of strength, durability, and performance.

Sail construction techniques also play a significant role in the performance and durability of a sail. Cross-cut sails are made from panels of fabric that are sewn together horizontally, following the natural lines of the fabric’s weave. This construction method is relatively simple and inexpensive but can result in a sail that is more prone to stretch and distortion. Radial-cut sails are made from panels of fabric that radiate out from the corners of the sail, distributing the loads more evenly and providing better shape retention and performance.

Understanding the different types of sails and their uses is essential for any sailor looking to optimize their sailing performance and enjoyment. By selecting the appropriate sails for your boat and the conditions you’ll be sailing in, you’ll be better prepared to navigate the open sea and embrace the freedom and fulfillment that comes from choosing an unconventional path.

Types of Sails: A Comprehensive Guide

In the enchanting world of sailboat dynamics, where the dance between wind and water takes center stage, the significance of sails cannot be overstated. Like the wings of a bird, these meticulously crafted sails unfurl to catch the slightest whisper of breeze, converting it into a powerful forward thrust that carries us through the vast expanse of the ocean. They are the very essence of a sailboat, the conduits through which dreams and aspirations set sail.

Join us on a captivating voyage as we unfurl the secrets of the myriad types of sails adorning the mastheads of sailboats across the globe. From the grandeur of the mainsail, proudly dominating the skyline, to the nimble headsails that steer with precision, and the enigmatic mizzensails that add an extra touch of finesse, we shall embark on a comprehensive exploration of the diverse array of sail types.

Different Types of Sails on a Sailboat: Why Use Different Sails at All?

Different sail types for different wind conditions.

Triangular sails, such as the mainsail and jib, are commonly used on modern sailboats to optimize performance when sailing upwind. The shape of these sails helps to create lift, which propels the boat forward even against the wind’s direction. The mainsail is attached to the mast at the front edge and a boom at the bottom. Jibs, on the other hand, are headsails that are attached to a stay near the bow of the boat.

Balloon sails, like spinnaker sails, are designed for downwind sailing and catching more wind to increase boat speed when sailing with the wind behind it. These types of sails have a large surface area that allows them to catch more wind than triangular sails. Spinnaker sails can come in different shapes depending on their intended use and can be flown from a spinnaker pole or directly from the bow.

Sail Plans: Different Combinations for Different Boats

Sail plans refer to how different types of sails are arranged and combined on a sailing craft. Sail plans can vary depending on specific design features and intended use of boats. For example, some boats may have multiple masts with several triangular-shaped sails attached while others may only have one mast with one triangular sail (mainsail) and one square sail (spinnaker). The combination of different types of sails can also affect how easy it is to handle a boat under certain conditions.

Understanding Sail Anatomy

Head, tack, foot, luff, leech, and clew. These are the different parts that make up a sail’s anatomy. But what exactly are they and why are they important? In this section, we’ll take a closer look at each part and how it contributes to the performance of a sailboat.

The Head: The Top of the Sail

Starting from the top, we have the head of the sail. This is where the halyard (the rope or wire used to hoist the sail) is attached. The head determines how high or low the sail sits on its mast. A higher head means more power but less control over the sail’s shape. Conversely, a lower head provides better control but less power.

The Tack: The Lower Front Corner of the Sail

Next is the tack which is found at the lower front corner of most sails. It’s where one end of a line called a “sheet” attaches to control how much wind enters through this corner of your sail. Adjusting your sheet will affect your boat’s speed and direction.

The Foot: The Bottom of the Sail

At the bottom edge of any sail lies its foot which helps determine its overall shape and size. Generally speaking, longer feet result in larger sails that provide more power while shorter feet result in smaller sails with better maneuverability.

The Luff: The Forward Edge of the Sail

The forward edge of any sail is called its luff which runs along its mast track or forestay depending on what type of rigging you have set up on your boat. It helps maintain proper airflow over your sails by keeping them from flapping around too much in high winds.

The Leech: The Back Edge of Your Sail

Opposite from your luff is your leech – or back edge – which helps create lift by allowing air to flow smoothly over your sail. A longer leech will result in a more powerful sail, while a shorter one will provide better control and maneuverability.

The Clew: The Bottom Back Corner of Your Sail

Lastly, we have the clew which is found at the bottom back corner of most sails. It’s where the other end of your sheet attaches to control how much wind enters through this corner of your sail. Adjusting your sheet here can affect how well you’re able to steer your boat.

Primary Sail Types

The main sail is attached to the main mast and boom and can be adjusted to match the wind conditions. Its main purpose is to keep the boat steady and under control by providing stability to the stern (back) of the vessel.

There are several variations of mainsails that sailors can choose from depending on their needs. One popular type of mainsail is an in-mast furling mainsail. This type of sail can be easily furled and unfurled by pulling a line, making it ideal for short-handed sailing or cruising. Another variation is a slab reefing mainsail, which has horizontal strips called battens that help maintain its shape. Finally, there is also a boom furling mainsail, which uses a roller system inside the boom to make it easier to handle.

A headsail is any sail located forward of the mast on a sailing vessel. These sails are designed to work in conjunction with the main sail to provide optimal performance under varying wind conditions. There are several types of headsails available, each with its own unique characteristics and purposes.

One popular type of headsail is known as a genoa. This large foresail extends beyond the mast and overlaps with the main sail, providing additional power when sailing upwind or reaching across wind angles. Genoas come in various sizes ranging from 110% up to 150%, depending on how much overlap you want.

Another common type of headsail is called a jib. This smaller foresail does not overlap with the main sail but instead works in conjunction with it. The jib is typically used in higher wind conditions when a smaller sail area is needed to maintain control of the boat.

A staysail is a smaller sail located between the mast and the forestay. This type of headsail is typically used on larger boats to provide additional power when sailing upwind or reaching across wind angles. Staysails are often used in conjunction with other sails, such as a genoa or main sail.

Finally, there is also a mizzensail, which is located aft of the main mast on ketches and yawls. This sail provides additional power when sailing downwind or reaching across wind angles. Mizzensails come in various sizes and can be either fully battened or free-flying.

Lightwind Sails

Spinnaker sails are a type of downwind sail that can be used to increase boat speed when sailing in light winds. They are typically used in wind conditions below 10 knots, which are considered light air sails. Spinnakers come in two types: symmetrical and asymmetrical.

Symmetrical vs Asymmetrical Spinnaker

The symmetrical spinnaker is designed to sail directly downwind or with the wind coming from behind the boat. It is shaped like a balloon, with equal amounts of material on both sides of the sail. The sail is attached to a spinnaker pole, which extends out from the mast and holds the sail away from the boat.

Asymmetrical spinnakers, on the other hand, are designed for sailing at angles off the wind. They have an uneven shape, with more material on one side than the other. This design allows them to be flown without a spinnaker pole, making them easier to handle for smaller crews.

Another type of downwind sail is called a gennaker. Gennakers are similar to asymmetrical spinnakers but have a hybrid characteristic between a spinnaker and a genua. They are designed for reaching or running downwind at higher speeds than traditional cruising chutes or asymmetric spinnakers.

For those who prefer an even more user-friendly option than asymmetrical spinnakers or gennakers, parasailors might be what you’re looking for! A parasailor combines aspects of both a traditional spinnaker and a parachute into one easy-to-use package. The unique design of this sail makes it ideal for use in light winds when other sails may not perform well enough.

Finally, there’s another type of upwind/downwind sail called the code zero. Code zeros are designed to be used in light winds when sailing upwind, but they can also be used for reaching and running downwind. These sails have a flat shape that allows them to generate lift even in very light wind conditions.

Heavy Weather Sails

Heavy weather sailing is a challenging and potentially dangerous activity. The use of heavy weather sails, such as trysails, is crucial to ensure the safety of sailors and their vessels.

A trysail is a small triangular sail made of heavy-duty material, typically spinnaker cloth or other lightweight fabric. It is designed to be used in stormy weather conditions when winds are high and the seas are rough.

The role of a trysail is to provide an alternative source of propulsion when the main sail or jib cannot be used. In addition, it helps reduce the heeling effect on the vessel caused by strong winds. Trysails are rigged using a separate halyard and can be set up quickly when needed.

A trysail should be used in severe weather conditions when winds exceed 40 knots or more. It is recommended that sailors practice setting up their trysail before they need it so that they can do it quickly and efficiently in an emergency situation.

Another type of heavy weather sail that every sailor should have on board is a storm jib. This sail is typically much smaller than a regular jib and made from heavier materials such as Dacron or nylon. Its purpose is to provide additional stability during high wind speeds and rough seas.

The features of a storm jib include its size, shape, and weight distribution. It has a large luff (the leading edge) which allows it to be hoisted higher up on the rigging than other sails. This helps keep the boat stable during high-speed sailing in strong winds.

A storm jib should be used in extreme weather conditions where wind speeds exceed 50 knots or more. When using this sail, it is important to ensure that the halyard is properly tensioned and that the sail is sheeted in tightly. This will help prevent any unnecessary movement or fluttering of the sail.

Overview Common Sail Types

100% of mainsail

Light – High

100% of foretriangle

Moderate – High

triangular, overlapping

110% – 150% of foretriangle

Light – Moderate

60% – 80% of foretriangle

Close Reach – Broad Reach

Lightwind, Downwind

balloon shape, free flying

200% of mainsail (or even more)

Broad Reach, Running

parachute shape

100% of spinnaker

80% – 85% of spinnaker

Lightwind, Upwind

75% of spinnaker

30% – 60% of mainsail

Mainsail, heavy weather

17.5% of mainsail (or less)

Headsail, heavy weather

max. 65% of the hight of the foretriangle

Unconventional Sails

Wing sails are a type of sail design that is not commonly used in traditional sailboat designs. They are essentially vertical airfoils that generate lift and propulsion by directing the wind over the surface of the sail. Wing sails have become increasingly popular in modern sailing craft, particularly in high-performance racing boats.

One of the main advantages of wing sails is their ability to produce a significant amount of power with very little heeling force. This means that they can be used effectively in high-wind conditions without causing the boat to tip over. Additionally, wing sails are highly efficient at sailing upwind, which allows sailors to point higher into the wind than with other types of sails.

While wing sails may seem like a relatively new concept, they have actually been around for quite some time. The first recorded use of a wing sail was by German engineer Wolfgang Zimmermann in 1959. Since then, many different variations on the design have been developed and tested.

Kite sails are another unconventional type of sail that has gained popularity in recent years. Unlike traditional downwind sails such as spinnaker or parasailors, kite sails are flown from a line attached to the bow of the boat and do not require a mast or boom.

Sail Materials and Technology

Traditional sail materials.

Sails have been used for thousands of years to harness the power of the wind and propel boats across water. Traditional sail materials were flax, hemp, or cotton. These natural fibers were woven together to create a strong, yet flexible material that could withstand the harsh conditions at sea. However, as technology advanced and sailors began to demand more from their sails, new materials were developed.

Modern Sail Materials

Modern sailboats use synthetic materials such as polyester, nylon, or laminated fabrics for their sails. These materials are lightweight and incredibly strong, allowing sailors to achieve greater speeds with less effort. They are also more durable than traditional sail materials and can withstand prolonged exposure to sunlight and saltwater.

Popular Sail and Mast Configurations

The sloop rig is one of the most popular sail plans for modern sailboats. It features a single mast and one headsail, like a jib or genoa. The mainsail is typically triangular in shape and hoisted up the main mast using a backstay to support it. The jib or genoa is attached to the forestay that runs from the top of the mast to the bow of the boat.

Another popular sail plan is the cutter rig, which also features a single mast but has two headsails – an overlapping jib and a smaller staysail. The mainsail is still triangular in shape and hoisted up the main mast with a backstay for support.

Moving onto two-masted rigs, we have ketch rig, which features a main mast and a shorter mizzen mast located in front of the rudder. The mainsail is still triangular in shape and hoisted up the main mast with a backstay for support, while the mizzen sail is generally smaller and triangular or quadrilateral in shape.

Lastly, we have the yawl rig which is similar to the ketch rig but has its shorter mizzenmast located aft of the rudder. The mainsail is still triangular in shape and hoisted up the main mast with a backstay for support, while the mizzen sail is generally smaller and triangular or quadrilateral in shape.

Conclusion: Understanding the Different Types of Sails

Understanding the Different Types of Sails is crucial for any sailor who wants to optimize their performance and safety on the water. Whether you’re racing, cruising or simply enjoying a day out on your sailboat, having the right sails for the conditions can make all the difference.

Ultimately, understanding the different types of sails is essential for any sailor looking to improve their skills on the water. By selecting the right sail for your boat and conditions, you can optimize your performance while staying safe and comfortable during your time at sea.

So whether you’re a seasoned sailor or just starting out, take some time to explore the various types of sails available and find the ones that work best for you. With a little knowledge and experience under your belt, you’ll be well on your way to mastering this exciting sport!

How do Boats Float? Exploring the Science Behind Buoyancy

Sailboats float because the average density of the boat is less than the density of water. When boats displace as much water as it weights, this is known as the buoyancy force generated by Archimedes’ principle. If you’ve ever wondered how do boats float and therefor enable us to embark on thrilling water adventures, you’ve…

How Does a Marine Toilet Work?

Have you ever wondered how a marine toilet works? If you’re planning to embark on a boating adventure or just curious about the mechanism of a marine toilet, this article is for you. Marine toilets work similarly to the ones on land with a bowl, a seat, and a flushing mechanism that uses water. However,…

Advantages of Catamaran Sailboat Charter

A catamaran sailboat charter is an exciting way to explore the beauty of the sea. Whether you are an experienced sailor or a first-timer, booking a catamaran sailboat charter has a lot of advantages that you can enjoy. In this article, we will discuss the advantages of booking a catamaran sailboat charter, so that you…

Monohulls vs. Catamarans: Which One is Best for You?

If you’re considering purchasing a sailboat, you might be wondering which type of vessel is best suited for your seafaring adventures. Fear not, for we’re here to help you weigh the differences between monohulls vs. catamarans to make an informed decision. Now, before we dive into the nitty-gritty details of hull design, sail handling, and…

Whats the Difference between Standing Rigging and Running Rigging?

Running rigging refers to the movable lines and ropes used to control the position and shape of the sails on a sailboat. Standing rigging, on the other hand, refers to the fixed wires and cables that support the mast and keep it upright. As the sun rises on another day, we find ourselves immersed in…

What is a Keel?: The Backbone of a Ship

As ships sail through tumultuous seas, their stability and maneuverability are tested to the fullest extent. The intricate design and engineering that go into a ship’s construction ensure that it can withstand the forces of nature and navigate through any challenging conditions. One of the most critical components of a ship’s design is the keel,…

Guide to Understanding Sail Rig Types (with Pictures)

There are a lot of different sail rig types and it can be difficult to remember what's what. So I've come up with a system. Let me explain it in this article.

What are the different types of sail rig? The sail rig is determined by the number of masts and the layout and shape of sails. Most modern ships are fore-and-aft rigged, while old ships are square-rigged. Rigs with one mast are sloops and cutters. Ketches, yawls, brigs, and schooners have two masts. Barques have three masts. Rigs can contain up to seven masts.

'Yeah, that's a gaff brig, and that a Bermuda cutter' - If you don't know what this means (neither did I) and want to know what to call a two-masted ship with a square-rigged mainsail, this article is definitely for you.

Sailboat in front of NYC with Bermuda mainsail and Jib

The Ultimate Guide to Sail Types and Rigs (with Pictures)

First of all, what is a sail rig? A sail rig is the way in which the sails are attached to the mast(s). In other words, it's the setup or configuration of the sailboat. The rig consists of the sail and mast hardware. The sail rig and sail type are both part of the sail plan. We usually use the sail rig type to refer to the type of boat.

Let's start by taking a look at the most commonly used modern sail rigs. Don't worry if you don't exactly understand what's going on. At the end of this article, you'll understand everything about rig types.

Diagram of most common rig types (Bermuda sloop, gaff cutter, gaff ketch, gaf schooner, full rigged ship)

The sail rig and sail plan are often used interchangeably. When we talk of the sail rig we usually mean the sail plan . Although they are not quite the same. A sail plan is the set of drawings by the naval architect that shows the different combinations of sails and how they are set up for different weather conditions. For example a light air sail plan, storm sail plan, and the working sail plan (which is used most of the time).

So let's take a look at the three things that make up the sail plan.

The 3 things that make up the sail plan

I want to do a quick recap of my previous article. A sail plan is made up of:

Mast configuration - refers to the number of masts and where they are placed
Sail type - refers to the sail shape and functionality
Rig type - refers to the way these sails are set up on your boat

I'll explore the most common rig types in detail later in this post. I've also added pictures to learn to recognize them more easily. ( Click here to skip to the section with pictures ).

How to recognize the sail plan?

So how do you know what kind of boat you're dealing with? If you want to determine what the rig type of a boat is, you need to look at these three things:

Check the number of masts, and how they are set up.
You look at the type of sails used (the shape of the sails, how many there are, and what functionality they have).
And you have to determine the rig type, which means the way the sails are set up.

Below I'll explain each of these factors in more detail.

The most common rig types on sailboats

To give you an idea of the most-used sail rigs, I'll quickly summarize some sail plans below and mention the three things that make up their sail plan.

Bermuda sloop - one mast, one mainsail, one headsail, fore-and-aft rigged
Gaff cutter - one mast, one mainsail, two staysails, fore-and-aft rigged
Gaff schooner - two-masted (foremast), two mainsails, staysails, fore-and-aft rigged
Gaff ketch - two-masted (mizzen), two mainsails, staysails, fore-and-aft rigged
Full-rigged ship or tall ship - three or more masts, mainsail on each mast, staysails, square-rigged

The first word is the shape and rigging of the mainsail. So this is the way the sail is attached to the mast. I'll go into this later on. The second word refers to the mast setup and amount of sails used.

Most sailboats are Bermuda sloops. Gaff-rigged sails are mostly found on older, classic boats. Square-rigged sails are generally not used anymore.

But first I want to discuss the three factors that make up the sail plan in more detail.

Ways to rig sails

There are basically two ways to rig sails:

From side to side, called Square-rigged sails - the classic pirate sails
From front to back, called Fore-and-aft rigged sails - the modern sail rig

Almost all boats are fore-and-aft rigged nowadays.

Square sails are good for running downwind, but they're pretty useless when you're on an upwind tack. These sails were used on Viking longships, for example. Their boats were quicker downwind than the boats with fore-and-aft rigged sails, but they didn't handle as well.

The Arabs first used fore-and-aft rigged sails, making them quicker in difficult wind conditions.

Quick recap from part 1: the reason most boats are fore-and-aft rigged today is the increased maneuverability of this configuration. A square-rigged ship is only good for downwind runs, but a fore-and-aft rigged ship can sail close to the wind, using the lift to move forward.

The way the sails are attached to the mast determines the shape of the sail. The square-rigged sails are always attached the same way to the mast. The fore-and-aft rig, however, has a lot of variations.

The three main sail rigs are:

Bermuda rig - most used - has a three-sided (triangular) mainsail
Gaff rig - has a four-sided mainsail, the head of the mainsail is guided by a gaff
Lateen rig - has a three-sided (triangular) mainsail on a long yard

The Bermuda is the most used, the gaff is a bit old-fashioned, and the lateen rig is outdated (about a thousand years). Lateen rigs were used by the Moors. The Bermuda rig is actually based on the Lateen rig (the Dutch got inspired by the Moors).

Diagram of lateen, gaff, and bermuda rig

Other rig types that are not very common anymore are:

Junk rig - has horizontal battens to control the sail
Settee rig - Lateen with the front corner cut off
Crabclaw rig

Mast configuration

Okay, we know the shape of the mainsail. Now it's time to take a look at the mast configuration. The first thing is the number of masts:

one-masted boats
two-masted boats
three-masted boats
four masts or up
full or ship-rigged boats - also called 'ships' or 'tall ships'

I've briefly mentioned the one and two mast configurations in part 1 of this article. In this part, I'll also go over the three-masted configurations, and the tall ships as well.

A boat with one mast has a straightforward configuration because there's just one mast. You can choose to carry more sails or less, but that's about it.

A boat with two masts or more gets interesting. When you add a mast, it means you have to decide where to put the extra mast: in front, or in back of the mainmast. You can also choose whether or not the extra mast will carry an extra mainsail. The placement and size of the extra mast are important in determining what kind of boat we're dealing with. So you start by locating the largest mast, which is always the mainmast.

From front to back: the first mast is called the foremast. The middle mast is called the mainmast. And the rear mast is called the mizzenmast.

Diagram of different mast names (foremast, mainmast, mizzenmast)

What is the mizzenmast? The mizzenmast is the aft-most (rear) mast on a sailboat with three or more masts or the mast behind the mainmast on a boat with two masts. The mizzenmast carries the mizzen sail. On a two-masted boat, the mizzenmast is always (slightly) smaller than the mainmast. What is the purpose of the mizzen sail? The mizzen sail provides more sail area and flexibility in sail plan. It can be used as a big wind rudder, helping the sailor to have more control over the stern of the ship. It pushes the stern away from the wind and forces the bow in the opposite way. This may help to bring the bow into the wind when at anchor.

I always look at the number of masts first, because this is the easiest to spot. So to make this stuff more easy to understand, I've divided up the rig types based on the number of masts below.

Why would you want more masts and sail anyways?

Good question. The biggest advantage of two masts compared to one (let's say a ketch compared to a sloop), is that it allows you to use multiple smaller sails to get the same sail area. It also allows for shorter masts.

This means you reduce the stress on the rigging and the masts, which makes the ketch rig safer and less prone to wear and tear. It also doesn't capsize as quickly. So there are a couple of real advantages of a ketch rig over a sloop rig.

In the case of one mast, we look at the number of sails it carries.

Boats with one mast can have either one sail, two sails, or three or more sails.

Most single-masted boats are sloops, which means one mast with two sails (mainsail + headsail). The extra sail increases maneuverability. The mainsail gives you control over the stern, while the headsail gives you control over the bow.

Sailor tip: you steer a boat using its sails, not using its rudder.

The one-masted rigs are:

Cat - one mast, one sail
Sloop - one mast, two sails
Cutter - one mast, three or more sails

Diagram of one-masted rigs (bermuda cat, bermuda sloop, gaff cutter)

The cat is the simplest sail plan and has one mast with one sail. It's easy to handle alone, so it's very popular as a fishing boat. Most (very) small sailboats are catboats, like the Sunfish, and many Laser varieties. But it has a limited sail area and doesn't give you the control and options you have with more sails.

The most common sail plan is the sloop. It has one mast and two sails: the main and headsail. Most sloops have a Bermuda mainsail. It's one of the best racing rigs because it's able to sail very close to the wind (also called 'weatherly'). It's one of the fastest rig types for upwind sailing.

It's a simple sail plan that allows for high performance, and you can sail it short-handed. That's why most sailboats you see today are (Bermuda) sloops.

This rig is also called the Marconi rig, and it was developed by a Dutch Bermudian (or a Bermudian Dutchman) - someone from Holland who lived on Bermuda.

A cutter has three or more sails. Usually, the sail plan looks a lot like the sloop, but it has three headsails instead of one. Naval cutters can carry up to 6 sails.

Cutters have larger sail area, so they are better in light air. The partition of the sail area into more smaller sails give you more control in heavier winds as well. Cutters are considered better for bluewater sailing than sloops (although sloops will do fine also). But the additional sails just give you a bit more to play with.

Two-masted boats can have an extra mast in front or behind the mainmast. If the extra mast is behind (aft of) the mainmast, it's called a mizzenmast . If it's in front of the mainmast, it's called a foremast .

If you look at a boat with two masts and it has a foremast, it's most likely either a schooner or a brig. It's easy to recognize a foremast: the foremast is smaller than the aft mast.

If the aft mast is smaller than the front mast, it is a sail plan with a mizzenmast. That means the extra mast has been placed at the back of the boat. In this case, the front mast isn't the foremast, but the mainmast. Boats with two masts that have a mizzenmast are most likely a yawl or ketch.

The two-masted rigs are:

Lugger - two masts (mizzen), with lugsail (a cross between gaff rig and lateen rig) on both masts
Yawl - two masts (mizzen), fore-and-aft rigged on both masts. Main mast is much taller than mizzen. Mizzen without a mainsail.
Ketch - two masts (mizzen), fore-and-aft rigged on both masts. Main mast with only slightly smaller mizzen. Mizzen has mainsail.
Schooner - two masts (foremast), generally gaff rig on both masts. Main mast with only slightly smaller foremast. Sometimes build with three masts, up to seven in the age of sail.
Bilander - two masts (foremast). Has a lateen-rigged mainsail and square-rigged sails on the foremast and topsails.
Brig - two masts (foremast), partially square-rigged. The main mast carries small lateen-rigged sail.

Diagram of two-masted rigs (gaff yawl, gaff ketch, gaff schooner, and brig)

The yawl has two masts that are fore-and-aft rigged and a mizzenmast. The mizzenmast is much shorter than the mainmast, and it doesn't carry a mainsail. The mizzenmast is located aft of the rudder and is mainly used to increase helm balance.

A ketch has two masts that are fore-and-aft rigged. The extra mast is a mizzenmast. It's nearly as tall as the mainmast and carries a mainsail. Usually, the mainsails of the ketch are gaff-rigged, but there are Bermuda-rigged ketches too. The mizzenmast is located in front of the rudder instead of aft, as on the yawl.

The function of the ketch's mizzen sail is different from that of the yawl. It's actually used to drive the boat forward, and the mizzen sail, together with the headsail, are sufficient to sail the ketch. The mizzen sail on a yawl can't really drive the boat forward.

Schooners have two masts that are fore-and-aft rigged. The extra mast is a foremast which is generally smaller than the mainmast, but it does carry a mainsail. Schooners are also built with a lot more masts, up to seven (not anymore). The schooner's mainsails are generally gaff-rigged.

The schooner is easy to sail but not very fast. It handles easier than a sloop, except for upwind, and it's only because of better technology that sloops are now more popular than the schooner.

The brig has two masts. The foremast is always square-rigged. The mainmast can be square-rigged or is partially square-rigged. Some brigs carry a lateen mainsail on the mainmast, with square-rigged topsails.

Some variations on the brig are:

Brigantine - two masts (foremast), partially square-rigged. Mainmast carries no square-rigged mainsail.

Hermaphrodite brig - also called half brig or schooner brig. Has two masts (foremast), partially square-rigged. Mainmast carries a gaff rig mainsail and topsail, making it half schooner.

Three-masted boats are mostly barques or schooners. Sometimes sail plans with two masts are used with more masts.

The three-masted rigs are:

Barque - three masts, fore, and mainmast are square-rigged, the mizzenmast is usually gaff-rigged. All masts carry mainsail.
Barquentine - three masts, foremast is square-rigged, the main and mizzenmast are fore-and-aft rigged. Also called the schooner barque.
Polacca - three masts, foremast is square-rigged, the main and mizzenmast are lateen-rigged.
Xebec - three masts, all masts are lateen-rigged.

Diagram of three-masted rigs (barque, full rigged ship)

A barque has three or four masts. The fore and mainmast are square-rigged, and the mizzen fore-and-aft, usually gaff-rigged. Carries a mainsail on each mast, but the mainsail shape differs per mast (square or gaff). Barques were built with up to five masts. Four-masted barques were quite common.

Barques were a good alternative to full-rigged ships because they require a lot fewer sailors. But they were also slower. Very popular rig for ocean crossings, so a great rig for merchants who travel long distances and don't want 30 - 50 sailors to run their ship.

Barquentine

The barquentine usually has three masts. The foremast is square-rigged and the main and mizzenmast fore-and-aft. The rear masts are usually gaff-rigged.

Faster than a barque or a schooner, but the performance is worse than both.

The polacca or polacre rig has three masts with a square-rigged foremast. The main and mizzenmast are lateen-rigged. Beautiful boat to see. Polacca literally means 'Polish' (it's Italian). It was a popular rig type in the Mediterranean in the 17th century. It looks like the xebec, which has three lateen-rigged masts.

Fun fact: polaccas were used by a Dutch sailor-turned-Turkish-pirate (called Murat Reis).

The xebec is a Mediterranean trading ship with three masts. All masts are lateen-rigged. I couldn't find any surviving xebecs, only models and paintings. So I guess this rig is outdated a long time.

A boat with three or more masts that all carry square-rigged sails is called a ship, a tall ship, or a full-rigged ship. So it's at this point that we start calling boats 'ships'. It has nothing to do with size but with the type of rigging.

More sails mean less stress on all of them. These ships use a lot of sails to distribute the forces, which reduces the stress on the rigging and the masts. Square sails mean double the sail area in comparison to triangular sails.

They are quite fast for their size, and they could outrun most sloops and schooners (schooners were relatively a lot heavier). The reason is that tall ships could be a lot longer than sloops, giving them a lot of extra hull speed. Sloops couldn't be as large because there weren't strong enough materials available. Try making a single triangular sail with a sail area of over 500 sq. ft. from linen.

So a lot of smaller sails made sense. You could have a large ship with a good maximum hull speed, without your sails ripping apart with every gust of wind.

But you need A LOT of sailors to sail a tall ship: about 30 sailors in total to ie. reef down sails and operate the ship. That's really a lot.

Tall ships are used nowadays for racing, with the popular tall ship races traveling the world. Every four years I go and check them out when they are at Harlingen (which is very close to where I live).

Check out the amazing ships in this video of the tall ship races last year near my hometown. (The event was organized by friends of mine).

What is the difference between a schooner and a sloop? A schooner has two masts, whereas the sloop only has one. The schooner carries more sails, with a mainsail on both masts. Also, sloops are usually Bermuda-rigged, whereas schooners are usually gaff-rigged. Most schooners also carry one or two additional headsails, in contrast to the single jib of the sloop.

What do you call a two-masted sailboat? A two-masted sailboat is most likely a yawl, ketch, schooner, or brig. To determine which one it is you have to locate the mainmast (the tallest). At the rear: schooner or brig. In front: yawl or ketch. Brigs have a square-rigged foremast, schooners don't. Ketches carry a mainsail on the rear mast; yawls don't.

What is a sloop rig? A sloop rig is a sailboat with one mast and two sails: a mainsail and headsail. It's a simple sail plan that handles well and offers good upwind performance. The sloop rig can be sailed shorthanded and is able to sail very close to the wind, making it very popular. Most recreational sailboats use a sloop rig.

What is the difference between a ketch and a yawl? The most important difference between a ketch and a yawl are the position and height of the mizzenmast. The mizzenmast on a yawl is located aft of the rudder, is shorter than the mainmast and doesn't carry a mainsail. On a ketch, it's nearly as long as the mainmast and carries a mainsail.

Pinterest image for Guide to Understanding Sail Rig Types (with Pictures)

There are a wonderful lots of DIY changeability shows on the cable airwaves these days.

Rick the rigger

There are SO many errors on this site it really should be taken down.

First major mistake is to say you are no longer afraid of the sea.

One that truly gets up my nose is the term ‘fully’ rigged ship. It’s a FULL rigged ship!! Your mast names are the wrong way round and just because there may be 3 it doesn’t automatically mean the one in the middle is the main.

I could go on and totally destroy your over inflated but fragile ego but I won’t. All I will say is go learn a lot more before posting.

Shawn Buckles

Thanks for your feedback. If you like to point out anything more specific, please let me know and I will update the articles. I’ve changed fully-rigged to full-rigged ship - which is a typo on my part. I try to be as concise as I can, but, obviously, we all make mistakes every now and then. The great thing about the internet is that we can learn from each other and update our knowledge together.

If you want to write yourself and share your knowledge, please consider applying as a writer for my blog by clicking on the top banner.

Thanks, Shawn

Well, I feel that I’ve learned a bit from this. The information is clear and well laid out. Is it accurate? I can’t see anything at odds with the little I knew before, except that I understood a xebec has a square rigged centre mainmast, such as the Pelican ( https://www.adventureundersail.com/ )

Hi, Shawn, You forgot (failed) to mention another type of rig? The oldest type of rig known and still functions today JUNK RIG!

Why are so many of the comments here negative. I think it is wonderful to share knowledge and learn together. I knew a little about the subject (I’m an Aubrey-Maturin fan!) but still found this clarified some things for me. I can’t comment therefore on the accuracy of the article, but it seems clear to me that the spirit of the author is positive. We owe you some more bonhomme I suggest Shawn.

As they say in the Navy: “BZ” - for a good article.

Been reading S.M. Stirling and wanted to understand the ship types he references. Thank you, very helpful.

This site is an awesome starting point for anyone who would like to get an overview of the subject. I am gratefull to Shawn for sharing - Thanks & Kudos to you! If the negative reviewers want to get a deeper technical knowledge that is accurate to the n-th then go study the appropriate material. Contribute rather than destroy another’s good work. Well done Shawn. Great job!

Good stuff Shawn - very helpful. As a novice, it’s too confusing to figure out in bits and pieces. Thanks for laying it out.

First of all I have to say that Rick ‘the rigger’ is obviously the one with the “over inflated but fragile ego” and I laughed when you suggested he share his knowledge on your blog, well played!

As for the content it’s great, hope to read more soon!

Alec Lowenthal

Shawn, I have a painting of a Spanish vessel, two masted, with. Lateen sails on both masts and a jib. The mainsail is ahead of the main mast (fore) and the other is aft of the mizzen mast. Would this be what you call lugger rig? I have not seen a similar picture. Thanks, Alec.

Thank you for your article I found easy to read and understand, and more importantly remember, which emphasises the well written.. Pity about the negative comments, but love your proactive responses!

This vessel, “SEBASTIAN” out of Garrucha, Almería, España, was painted by Gustave Gillman in 1899.

Sorry, picture not accepted!

Thank you for a very informative article. I sail a bit and am always looking for more knowledge. I like the way you put forth your info and I feel if you can’t say anything positive, then that person should have their own blog or keep their opinions to their-self. I will be looking for more from you. I salute your way of dealing with negative comments.

Thank you for a great intro to sailing boats! I searched different sailboats because I use old sails tp make bags and wanted to learn the difference. Way more than I ever expected. Thanks for all the work put in to teach the rest of us.

Your description of a cutter is lacking, and your illustrations of “cutters” are actually cutter-rigged sloops. On a true cutter, the mast is moved further aft (with more than 40% of the ship forward of the mast). A sloop uses tension in the backstay to tension the luff of the foresail. The cutter can’t do this.

Also, a bermuda-rigged ketch will have a line running from the top of the mainmast to the top of the mizzenmast.

wow great guide to rig types! thanks

Interesting guide, however I am confused about the description of the brig. You say the main mast on a brig can have a lateen sail, but in your picture it looks like a gaff sail to me. How is it a lateen sail?

Hi Shawn, thank you for taking the time to share this information. It is clear and very helpful. I am new to sailing and thinking of buying my own blue water yacht. The information you have supplied is very useful. I still am seeking more information on performance and safety. Please keep up the good work. Best Regards

mickey fanelli

I’m starting to repair a model sailboat used in the lake I have three masts that have long been broken off and the sails need replacement. So my question is there a special relationship between the three masts I do have reminents of where the masts should go. they all broke off the boat along with the sails I can figure out where they go because of the old glue marks but it makes no sense. or does it really matter on a model thank you mickey

Cool, total novice here. I have learnt a lot. Thanks for sharing - the diagrams along with the text make it really easy to understand, especially for a beginner who hasn’t even stepped on a sailing boat.

Daryl Beatt

Thank you. Cleared up quite a few things for me. For example, I was familiar with the names “Xebecs” and “Polaccas” from recent reading about the Barbary War. I had gathered that the two Barbary types were better suited to sailing in the Med, but perhaps they were less able to be adaptable to military uses,(but one might assume that would be ok if one plans to board and fight, as opposed to fight a running gun duel). Specifically, the strangely one sided August 1, 1801 battle between the USS Enterprise under Lt. John Sterett and the Polacca cruiser Tripoli under Admiral Rais Mahomet Rous. On paper both ships seemed nearly equal in size, guns and crew, but pictures of the battle are confusing. While the Enterprise is usually rendered as the familiar schooner, the polacca Tripoli has been pictured in radically different ways. Thus the Wikipedia picture by Hoff in 1878 used to illustrate the Battle shows a Brig design for Tripoli, indicating 77 years later, polaccas were no longer common.

Lee Christiansen

I am curious as to what you would call a modern race boat with a fractional jib,not equipped for full masthead hoist? Thanks Lee

Thanks Guy: The information and pictures really eliminate a lot of the mystery of the terminology and the meanings. Also appreciate the insight of the handling idiosyncrasies “hand” (staff) requirements to manage a vessel for one that has not been on the water much. I long to spend significant time afloat, but have concern about the ability to handle a vessel due to advancing age. The Significant Other prefers to sit (in AC comfort)and be entertained by parties of cruise line employees. Thanks again for the information.

Gordon Smith

Your discussion made no mention of the galleon, a vessel with either square-rigged Fore and Main masts and a shorter lateen-rigged Mizzen, or, on larger galleons, square-rigged Fore and Main masts, with a lateen-rigged Mizzen and a lateen-rigged Bonaventure mast, both shorter than either the Fore or Main masts. Also, it was not uncommon for a galleon to hoist a square-rigged bowsprit topsail in addition to the usual square-rigged spritsail.

17 Sailboat Types Explained: How To Recognize Them

Birdseye view of beach and coastline with lots of small sailboats

Different Types of Sailing and Racing Explained

Italian sailboats with blue sails competing in sunny weather

How Are Sail Numbers Assigned? (And how to pick yours)

Better Sailing

Names of Sails on a Sailboat

Are you a beginner sailor and want to get acquainted with the names of the sails? Are you an experienced sailor and want to learn more details about the sails on a sailboat? Then this article is written for you! Sails form a crucial part of the sailboat because without them, there’s no starting up. For that reason, there are many details about different types of sails concerning their utility, functionality, fabrication materials, and performance. Simply put, each sail serves different purposes when out on the water. Since the sail is the engine of your sailboat, in terms of it being the basic source of propulsion, it’s important to know when best to use either type of sail and why.

Types of Sails on a Sailboat

So, in order to better explain the types of sails, let’s look at their characteristics. The first important distinction between sails is their placement. Generally, the mainsail is placed aft of the mast , which means behind. On the contrary, the headsail is in front of the mast. There are also other sorts of sails that are used for specific conditions. These can be the spinnakers or balloon-shaped sails for downwind use. The second important distinction for the sails is their functionality. The specialized sails have different functionalities and are used in different sailing circumstances and weather conditions. A rule about sails is that large sails are appropriate for downwind use, whereas small sails are good for upwind use. Moreover, large sails perform better on weak winds while small sails are good for strong winds.

The Parts of a Sail and its Shapes

Head: This is the top of the sail.
Luff: The forward edge of the sail.
Leech: Back edge of the sail.
Tack: The lower front corner of the sail.
Clew: The bottom back corner of the sail.
Foot: Bottom of the sail.

There are two sail shapes, the fore-and-aft rigged sails, and square-rigged sails. Nowadays, fore-and-aft sails are more popular, have better performance and maneuverability. To grasp the idea square sails are the ones that Vikings had on their ships and are good at sailing downwind because they run from side to side. But they’re not suitable at all when sailing upwind. On the other hand, a fore-and-aft sail is tied from the front of the mast to the stern and is much better at sailing upwind.

Types and Names of Sails

There are a lot of reasons why you’d want to put one sail over another, but the most important thing to remember has to do with the point of your sail and the wind strength. These points help you understand how your sailboat generates wind power. These points of sail include: into the wind (in irons), beam-reaching, broad-reaching, close-hauled, close-reaching, and running. They all go from windward to leeward and are symmetric from port to starboard . So, let’s get to the point and see the names and explanation of each sail:

Mainsail : The large sail behind the mast which is attached to the mast and the boom, is called the mainsail. Mainsails cover a lot of surface area concerning incoming winds and by doing that they don’t need very strong winds to provide forward propulsion on a sailboat.
Headsail or Jib : The small sail placed in front of the mast, attached to the mast and forestay (ie. jib or genoa), is called the headsail. Headsails are smaller than mainsails, thus their surface area is smaller. As a result, they can’t catch the same wind as a mainsail does. However, this is important because in case that the current wind is strong and the mainsail has been enough trimmed, being able to remove the mainsail and depend on the headsail alone, is a good strategy in order to reduce speed.
Genoa : A genoa is like a large jib and it’s attached to the front of the forestay, like a headsail. When you use a genoa sail then you are expecting light to medium winds. Also, your sailboat would be somehow in a rush point of sail, meaning that the wind comes directly from the rear. Moreover, the surface area of a genoa sail is quite large, so it’s important to use it when winds are relatively low.
Spinnaker : These downwind sails are symmetrical which makes them more sensitive to the reaching points of the sail and therefore more suitable for the running point of sail. Spinakkers are lighter than other types of jibs, and they don’t cover the mast like a genoa sail. Moreover, they remain unattached to the forestay and stretch out toward and past the bow of a sailboat.
Gennaker : Gennakers are a mixture of genoa and spinnaker sails. There are small and big gennakers and both are downwind sails. They aren’t as symmetric as a spinnaker and aren’t attached to the forestay like a headsail. Furthermore, the gennaker sail is able to take on a more flexible point of sail while taking advantage of softer winds.
Drifter Reacher : A drifter is a light air sail, and it’s basically a larger genoa for use in light winds. Its extra sail area offers better downwind performance than a genoa. It’s mostly made from lightweight nylon.
Code Zero Reacher : This sail is a type of spinnaker, but it looks like a large genoa. However, code zero is designed for better reaching which makes it much flatter than the spinnaker.
Windseeker : This sail is small, and it’s designed to guide light air onto the lee side of the mainsail. Moreover, it’s tall and thin and ensures a smoother flow of air.

Sail and Mast Configurations

Now that you got an idea of the different types of sails on a sailboat, it would also be an advantage to know how these types of sails are related to the configuration of a sailboat’s mast. There are numerous combinations when it comes to sails and mast configurations, let’s see some of them!

Cat: A cat is similar to a dinghy and has one mast and one sail. The mast is located at the bow of the sailboat.
Sloop: The sloop has the classic single mast and a double sail setup. The headsail can be different kinds of jibs, is connected with the forestay on the mast, and runs all the way up to the mast.
Fractional Rig Sloop: A fractional rig sloop is different from the sloop because its forestay doesn’t reach the top of the mast. Its headsail is restricted to a fractional amount of space and this means that less wind can be captured, therefore the speed of the sailboat is reduced.
Cutter: Having two forestays on the mast and cutters that are able to house two headsails this setup allows easy cruising because it offers a wide combination of points of sail for different strengths of wind.
Ketch: Just like a sloop the ketch has a mast that enables the mainsail and headsail to a full range forestay. However, it also has a smaller mast between the mainmast and the stern of the sailboat.
Schooner: A schooner is when a sailboat has two or more masts but it has a couple of sails to manage. A schooner’s aft mast is taller than the forward mast and sometimes a schooner can have up to six masts.

Names of Sails on a Sailboat – Summary

So, how many types of sails are there? In general, sailboats have one mainsail and one headsail. The rigging also affects the types of sails you can use. As we’ve explained before, the mainsail is a fore-and-aft Bermuda rig. Then, for a headsail, we use a jib or genoa. Most experienced sailors use extra sails to ensure better performance for their sailboat. For example, the spinnaker (a common downwind sail), the gennaker, the code zero (for upwind use), and the storm sail. Keep in mind that every sail has its own use and performance. Want to go downwind fast? Use a spinnaker. Don’t just raise any sail you think suits you best and go for it! It’s of great importance to understand the functionality, use, and performance of each sail.

Peter is the editor of Better Sailing. He has sailed for countless hours and has maintained his own boats and sailboats for years. After years of trial and error, he decided to start this website to share the knowledge.

Lagoon Catamaran Review: Are Lagoon Catamarans Good?

Best Inboard Boat Engine Brands

Are O’Day Sailboats Good? A Closer Look at a Classic Brand

Why Do Sailboats Lean?

Buyer's Guide
Destinations
Maintenance
Sailing Info

Hit enter to search or ESC to close.

Types of Sails for Sailboats: A Comprehensive Guide

by Emma Sullivan | Jul 28, 2023 | Sailboat Racing

Short answer types of sails for sailboats:

Sailboats typically use four primary types of sails: mainsails, genoas/jibs, spinnakers, and staysails. Mainsails are the largest and provide forward propulsion. Genoas/jibs enable efficient sailing upwind. Spinnakers are used for downwind sailing and maximizing speed. Stay-sails provide stability in heavy wind conditions.

Understanding the Basics: Different Types of Sails for Sailboats

Sailing is not just a passion but a way of life for many people. Whether you are an experienced sailor or just starting out, understanding the different types of sails for sailboats is essential to navigate the vast seas. In this blog post, we will delve into the basics of sail types, their functionalities, and how they can enhance your sailing experience.

1. The Mainsail: Starting with the star of the show, the mainsail is the largest and most important sail on a sailboat. It is typically positioned behind the mast and provides primary propulsion when sailing upwind or reaching across different wind angles. With its triangular shape, it catches wind efficiently and drives the boat forward like a well-oiled engine.

2. The Genoa or Jib: Next in line is the genoa or jib sail (pronounced ‘jīb’) that complements the mainsail perfectly. Positioned at the bow, it adds extra horsepower to help propel the boat forward even faster. The genoa sail offers versatility by allowing adjustment to different wind conditions without compromising speed and agility.

3. The Spinnaker: Often called “the wild card” among sails, spinnakers come in vibrant colors and are usually used for downwind sailing situations. When deployed, this balloon-shaped beauty fills with air like a parachute, harnessing every ounce of wind power available – perfect for exhilarating rides in light breeze conditions. However, handling a spinnaker requires skill as it can become untamable when winds pick up speed!

4. The Storm Sail: Just like its name suggests, storm sails are designed specifically for rough weather conditions – think rainstorms and gale-force winds! Smaller in size compared to other sails on board, these heavy-duty wonders provide stability during adverse weather situations by ensuring that sailors stay safe while navigating through treacherous waters.

5. The Gennaker: A combination of genoa and spinnaker, the gennaker is a true hybrid sail. Perfect for reaching and running downwind, it comes in handy when you want to sail at higher speeds without dealing with the complexity of managing a traditional spinnaker. Its lightweight nature and ease of control make it an excellent choice for both racing enthusiasts and leisurely cruisers alike.

Now that we’ve covered some key types of sails, it’s important to note that each sail type has various designs within its category. These designs cater to specific sailing conditions, such as heavy winds or light breezes, ensuring optimal performance during your time on the water.

Before wrapping up, let’s briefly touch on the importance of choosing the right sails for your sailboat. The type of sail you select can significantly impact your sailing experience – from optimizing speed and maneuverability to ensuring safety while exploring new horizons. Therefore, consulting with experienced sailors, researching different options, and considering factors such as boat size and intended use are crucial steps in making an informed decision.

In conclusion, understanding the basics of different types of sails for sailboats is vital for anyone stepping into this exciting world. From the powerful mainsail to the versatile genoa or jib, each sail plays a unique role in enhancing your sailing experience. So whether you’re looking to set out on lengthy ocean crossings or simply enjoy peaceful coastal cruises, knowing your sails will help you navigate every nautical mile with confidence and style!

Choosing the Right Sail: A Step-by-Step Guide to Types of Sails for Sailboats

Welcome to our blog where we will embark on a sailing adventure and explore the intricate world of sail selection. Choosing the perfect sail for your sailboat can seem like a daunting task, but fear not! We are here to break it down step-by-step and help you navigate through the vast sea of options. So grab your compass and let’s set sail!

Step 1: Assess your Sailing Style Before diving into the ocean of sail choices, it’s important to identify your sailing style. Are you a casual cruiser who enjoys leisurely trips across calm waters? Or do you yearn for thrilling high-speed races under challenging conditions? Determining this will play a vital role in selecting the most suitable sails for your needs.

Step 2: Consider Sail Material The material used in constructing sails significantly impacts their performance and longevity. Traditional woven Dacron sails are cost-effective, durable, and ideal for recreational sailors. However, if you’re an avid racer or prefer enhanced performance in varying wind conditions, composite laminated sails might be worth exploring.

These advanced sails utilize lightweight materials like carbon fiber or Kevlar, providing exceptional strength-to-weight ratios that optimize speed and maneuverability. Just keep in mind that these high-performance sails often come with a higher price tag.

Step 3: Understanding Sail Shapes Sail shape directly affects how efficiently your boat harnesses wind power. Depending on your sailing intentions, different shapes offer distinct advantages:

a) Bermuda Rig: This popular triangular mainsail design is commonly found on cruising boats due to its versatility. It offers easy handling and adaptability to various wind angles.

b) Gaff Rig: If you appreciate traditional aesthetics combined with robust downwind performance, gaff rig may satisfy your desires. Its distinctive four-sided configuration enables larger sail area while maintaining control during gusty conditions.

c) Cat Rig: Designed for simplicity and ease of use, cat rigs feature a single mast and sail, usually located at the front of the boat. This setup is excellent for beginners or those seeking a straightforward sailing experience.

Step 4: Size Does Matter Now that we’ve covered shapes let’s discuss the importance of sail size. Sailboat sizes can vary significantly, ranging from small dinghies to massive ocean-crossing yachts. Matching your sail size to your boat’s specifications ensures optimal performance and safety on the water.

Factors such as wind conditions in your local area, desired speed, and crew abilities must also be considered when determining the ideal sail size.

Step 5: Seek Expert Advice When in doubt, enlist the knowledge and assistance of professionals in the sailing community. Local sailmakers or experienced sailors can provide valuable insights catered specifically to your needs. They possess a wealth of firsthand information regarding local conditions, popular sails within your sailing community, and potential upgrades that could elevate your sailing experience.

So there you have it! A step-by-step guide to choosing the right sails for your sailboat. By assessing your sailing style, considering materials and shapes, properly sizing your sails, and seeking expert advice, you’ll be well on your way to embarking on unforgettable voyages atop glistening waves.

Remember that selecting the perfect sails for any sailor is ultimately an art as much as a science – enjoy exploring this exciting world while keeping safety and performance at heart!

Frequently Asked Questions About Types of Sails for Sailboats

Welcome to our blog where we aim to provide you with detailed, professional, witty, and clever explanations on frequently asked questions about types of sails for sailboats. Whether you are a seasoned sailor or just starting your sailing journey, understanding the different types of sails available is crucial for maximizing your boating experience. So, let’s dive in!

1. What are the different types of sails commonly used in sailboats?

Ahoy! When it comes to sailboat sails, you’ll often encounter three main types: mainsails, headsails (also known as jibs), and spinnakers. Each serves a specific purpose and contributes differently to the overall sailing performance.

– Mainsails: The largest and most important sail on a boat, mainsails are primarily responsible for propelling the vessel forward. Positioned behind the mast, they generate power through their large surface area and can be adjusted using various controls like boom vangs and cunninghams.

– Headsails/Jibs: Located at the bow of the boat, headsails come in various sizes such as genoas or jibs. Jibs are generally smaller than genoas but offer better maneuverability in heavier winds. These sails help balance the forces acting on the boat by providing lift from the front.

– Spinnakers: For those seeking exhilaration on reaching or downwind courses, spinnakers are a must-have! These big billowy sails catch wind from behind and enable higher speeds. Used in lighter winds when sailing off course or downwind, they can turn an ordinary sail into an extraordinary adventure.

2. Which type of sail should I use during upwind sailing?

When battling against the wind while navigating upwind (or close-hauled), it’s essential to hoist your headsail/jib rather than relying solely on your mainsail. This combination allows for efficient airflow diversion around both sides of your boat – creating that sought-after lift required to sail efficiently and beat upwind.

3. Are there any sail types specifically designed for downwind sailing?

Absolutely! For a fantastic downwind experience, you’ll want to unleash the power of a spinnaker. These beautifully large sails are uniquely shaped to capture every gust of wind from behind, propelling your boat at exhilarating speeds. But beware, handling a spinnaker can be quite challenging, so practice and caution are vital.

4. Can I use more than one headsail on my sailboat?

Ahoy mates, this is where it gets exciting! Sailors often employ multiple headsails simultaneously for enhanced maneuverability and increased propulsion. Known as “sail combinations,” common setups include using both a jib and genoa together or even deploying two genoas with different sizes at once – affording great control options in varying wind conditions.

5. How do sails differ in shape and material construction?

Sails come in various shapes and constructions tailored for specific purposes. The materials used range from traditional woven fabrics like Dacron (popular for its durability) to high-performance laminated fabrics such as Kevlar or carbon fiber composites (offering increased strength but potentially at higher costs). Each material has its advantages, so it’s crucial to choose the right sail based on your sailing goals, preferences, and budget.

So there you have it, sailors – an informative yet entertaining rundown of frequently asked questions about types of sails for sailboats. Remember that selecting the appropriate sails depends on numerous factors like wind conditions, desired speed, boat size/type, and personal preference. Now go out there, catch the wind in your sails, and embark on unforgettable nautical adventures!

Exploring the World of Main Sails: An In-Depth Look at Types and Features

Title: Exploring the World of Main Sails: An In-Depth Look at Types and Features

Introduction: Welcome aboard, fellow adventure-seekers! Today, we embark on an exhilarating journey into the enchanting realm of main sails. As sailors, we understand the pivotal role that these magnificent pieces of cloth play in driving our vessels forward. So, let us unfurl our curiosity as we delve into the vast expanse of main sail types and features. From traditional designs to cutting-edge innovations, fasten your seatbelts or rather hoist your clew lines; for it’s time to set sail on this epic exploration!

Main Sail Types: 1. Bermuda Rig: This timeless and widely used design originates from Bermuda (hence the name) and showcases a triangular shape with a pronounced mast incline. Known for its versatility and effectiveness across various wind conditions, the Bermuda rig offers superb control while maintaining desirable speed.

2. Gaff Rig: Picture a charming vintage schooner gracefully sailing across crystal-clear waters under an expansive gaff-rigged main sail – pure nautical bliss! Here, a wooden spar called a gaff supports the top edge of the sail, allowing for easier manipulation during maneuvers without sacrificing performance.

3. Lateen Sail: Embark on an exotic journey to distant shores with the lateen sail adorning your vessel. Hailing from ancient maritime civilizations such as Egypt and Phoenicia, this triangular sail is rigged with its base along one side of the boat—a sight that effortlessly evokes captivating tales from seafaring lore.

4. Junk Rig: Pay homage to centuries-old Chinese traditions by embracing a junk rig main sail configuration – perfect for those who crave a taste of both beauty and functionality in their sailing escapades. With multiple battens enhancing structural stability while reducing stress on individual components, this unconventional yet ingenious setup unlocks exciting possibilities in terms of ease-of-use and adaptability.

Main Sail Features: 1. Battens: These slender, lightweight rods serve as key components within a sail, improving its shape retention by preventing unwanted fluttering and enhancing overall efficiency. Modern main sails often boast battens made from sturdy materials like carbon fiber or fiberglass for optimal durability.

2. Luff Systems: Achieving precise control of the leading edge of the main sail is crucial to maximizing performance. Here, the choice between traditional hanks or convenient luff slides and cars comes into play – seamlessly balancing heritage with modernity while enabling ease of reefing and tweaking for swift adjustments.

3. Headboards: Crown jewels atop our main sails! These structures reinforce the upper portion, ensuring longevity by distributing stress during rough weather conditions. Ingenious evolution has given rise to lightweight alternatives such as carbon-fiber headboards that offer exceptional strength while minimizing weight aloft.

4. Reefing Mechanisms: Navigating formidable seas sometimes calls for reducing sail area to maintain stability and safety onboard. With various reefing systems at our disposal, like slab reefing or in-mast furling, we can swiftly decrease the main sail’s size while retaining ultimate control over your vessel’s destiny!

Conclusion: Ahoy fellow adventurers! We have traversed uncharted territories on this voyage through the enchanting world of main sails—unveiling their mesmerizing types and navigating their irresistible features along the way! Whether you favor tradition or embrace innovation with open arms, it’s clear that every sailor possesses unique preferences when it comes to these majestic fabrics that propel us forward into breathtaking oceanscapes. So, hoist your favorite mainsail high and let winds carry you toward endless horizons as you embark on extraordinary maritime exploits!

Jib or Genoa? Unraveling the Differences in Types of Headsails for Sailboats

When it comes to headsails for sailboats, there are two popular options that often leave sailors scratching their heads: jibs and genoas. Understanding the differences between these two types of headsails is crucial for making informed decisions on the water. So, let’s weigh anchor and set sail into unraveling the mysteries behind jibs and genoas.

Starting with the basics, a headsail is any sail set forward of the mast, aiding in propulsion by capturing wind energy. Now, onto our contenders – the jib and genoa!

A jib is traditionally defined as a headsail that is smaller than 100% of a boat’s foretriangle – that triangular area between bow, mast, and forestay. This compact size allows for enhanced maneuverability and responsiveness in challenging wind conditions. Jibs come in various sizes, including the storm jib (ideal for heavy weather) and the working jib (perfect for moderate breezes). If you’re aiming to finesse your way through tight spots or swiftly navigate crowded marinas, a jib might be your trusted mate.

On the other hand, we have our vivacious challenger – the genoa! Unlike its smaller cousin, a genoa spans beyond 100% or even up to 150% of a vessel’s foretriangle. Picture an oversized butterfly wing gracefully caressing through the air. Genoas provide tremendous power when sailing upwind or reaching under lighter wind conditions due to their substantial surface area.

Now you may ask yourself: “Why would I need all that extra canvas flapping about?” Well, dear sailor, here’s where physics enters our nautical narrative! A larger sail area means more lift generated by airflow over its surface. This added lift helps counteract heeling forces caused by wind pressure on other sails (mainly your mainsail), thereby improving stability and reducing strain on both crew and rigging.

But beware! With great power comes some caveats. Handling a genoa can be quite daunting when winds pick up or narrow channels beckon for precise maneuvering. Its increased size may hinder boat agility and make tacking (turning into the wind) a delicate dance with unpredictable results.

Ultimately, your choice between a jib and genoa depends on several factors: sailing style, prevailing weather conditions, crew size, and boat design. For spirited sailors seeking fast-paced thrills or seasoned racers trying to outpace competitors, the performance of a genoas’s extra sail area unquestionably tickles their fancy.

Meanwhile, those leisurely cruising along calm waters might favor the nimbleness of a jib that effortlessly responds to steering inputs.

Remember, dear sailor – understanding these trade-offs allows you to harness the wind more effectively. So weigh your options wisely before hoisting your favorite headsail type atop its lofty perch!

In conclusion, whether you opt for a diminutive jib or embrace the allure of an expansive genoa, each headsail brings its own unique sailing experience. Just like choosing between a swift steed or a graceful partner in dance, finding the perfect match requires careful consideration – for it is this match that will carry you across vast oceans or whisk you away to secluded coves. Ahoy!

All About Specialty Sails: Discovering Unique Types for Specific Wind Conditions

Sailing is not just a sport or hobby; it’s an art that requires skill, precision, and a deep understanding of the elements. One crucial factor that can make or break your sailing experience is the type of sail you choose. Just as different brushes serve various painting techniques, specialty sails are designed to address specific wind conditions. In this blog post, we will dive into the depths of specialty sails, exploring their unique types and unveiling the secrets behind matching them to specific wind conditions.

1. Battened Mainsail: Let’s start with one of the most common specialty sails used in sailing – the battened mainsail. This sail is equipped with long, lightweight battens that run parallel to its leech edge, enhancing its ability to maintain shape and stability. Suitable for light winds and cruising situations, the battened mainsail ensures optimal control even when gusts try to play tricks on you.

2. Genoa: When it comes to flying through moderate winds with grace and speed, every sailor worth their salt knows about the mighty genoa. This specially designed foresail boasts a larger overlapping area compared to a jib and can adapt seamlessly to various wind angles without compromising maneuverability. Whether you’re racing or embarking on an adventurous voyage, having a genoa onboard will give you that extra oomph!

3. Spinnaker: Are you craving adrenaline-pumping downwind rides? Then look no further than the spinnaker – often referred to as a “kite” due to its distinctive shape and vibrant colors! This asymmetric sail is made for strong winds blowing from behind your vessel’s beam or even dead astern. Its massive size catches every gust available, propelling you forward in exhilarating bursts over endless blue waters.

4. Storm Sail: Mother Nature holds many surprises up her sleeve, including unexpected storms that can leave even the most experienced sailors feeling like novices. This is when a storm sail comes to the rescue. Made from heavy-duty material and featuring a smaller hoist, this compact sail keeps you safe, stable, and in control when strong winds threaten to overpower your vessel.

5. Code Zero: Meet the ultimate weapon for light wind sailing – the code zero. Ideal for symmetrical or asymmetrical layouts, this specialty sail offers exceptional performance in extremely light wind conditions. Its distinctive design allows it to harness even the slightest breeze with minimal drag, effortlessly propelling your boat forward when other sails would hang limp.

6. Gennaker: Imagine combining the best of both worlds – the speed and power of a spinnaker with the ease of use of a genoa. Enter gennakers! Perfect for those cruising days where optimal performance is paired with user-friendly handling, these specialized sails bring joy to sailors looking for an all-around solution in moderate wind situations.

The world of specialty sails goes far beyond what we’ve explored here today, but this overview should give you a taste of their fascinating variety and purposefulness. These unique sails are meticulously crafted by experts who understand not only their complex aerodynamics but also how they interact with different wind conditions to unlock your vessel’s true potential.

So next time you embark on a sailing adventure, take into consideration the specific wind conditions you may encounter and make sure to equip yourself with the right specialty sail that will turn your voyage into an extraordinary experience worth cherishing. Happy sailing!

Distinguishing Types of Sailboats

In this article, we'll distinguish sailboats by traits such as their hull type, rig, and general configuration. Some sailboats share multiple characteristics with other boats but fall into a completely different category. For example, a sailboat with a Bermuda rig, a large engine, and a pilothouse could technically be called a sloop, but it's more likely a motorsailer.

When discerning sailboat type, the first most obvious place to look is the hull. If it has only one hull, you can immediately eliminate the trimaran and the catamaran. If it has two or more hulls, it's certainly not a typical monohull vessel.

The next trait to consider is the rig. You can tell a lot about a sailboat based on its rig, including what it's designed to be used for. For example, a long and slender sailboat with a tall triangular rig is likely designed for speed or racing, whereas a wide vessel with a complex gaff rig is probably built for offshore cruising.

Other factors that determine boat type include hull shape, overall length, cabin size, sail plan, and displacement. Hull material also plays a role, but every major type of sailboat has been built in both wood and fiberglass at some point.

Sailboat vs. Motorsailer

Most sailboats have motors, but most motorized sailboats are not motorsailers. A motorsailer is a specific kind of sailboat designed to run efficiently under sail and power, and sometimes both.

Most sailboats have an auxiliary engine, though these power plants are designed primarily for maneuvering. These vessels cannot achieve reasonable speed or fuel-efficiency. Motorsailers can operate like a powerboat.

Motorsailers provide great flexibility on short runs. They're great family boats, and they're popular in coastal communities with heavy boat traffic. However, these features come at a cost. Motorsailers aren't the fastest or most efficient powerboats, and they're also not the most agile sailboats. That said, they make an excellent general-purpose sailing craft.

Monohull vs. Multi-hull: Which is Better?

Multihull sailboats are increasingly popular, thanks to advances and lightweight materials, and sailboat design. But are they better than traditional sailboats? Monohulls are easier to maintain and less expensive, and they offer better interior layouts. Multihulls are more stable and comfortable, and they're significantly easier to control. Multihull sailboats also have a speed advantage.

Monohull Sailboats

A monohull sailboat is a traditionally-shaped vessel with a single hull. The vast majority of consumer sailboats are monohulls, as they're inexpensive to produce and easy to handle. Monohull sailboats are proven and easy to maintain, though they lack the initial stability and motion comfort of multi-hull vessels.

Monohull sailboats have a much greater rig variety than multi-hull sailboats. The vast majority of multihull sailboats have a single mast, whereas multi-masted vessels such as yawls and schooners are always monohulls. Some multi-hull sailboats have side-by-side masts, but these are the exception.

Catamaran Sailboats

The second most common sailboat configuration is the catamaran. A catamaran is a multihull sailboat that has two symmetrical hulls placed side-by-side and connected with a deck. This basic design has been used for hundreds of years, and it experienced a big resurgence in the fiberglass boat era.

Catamarans are fast, efficient, and comfortable. They don't heel very much, as this design has excellent initial stability. The primary drawback of the catamaran is below decks. The cabin of a catamaran is split between both hulls, which often leaves less space for the galley, head, and living areas.

Trimaran Sailboats

Trimarans are multi-hull sailboats similar to catamarans. Trimarans have three hulls arranged side-by-side. The profile of a trimaran is often indistinguishable from a catamaran.

Trimarans are increasingly popular, as they're faster than catamarans and monohulls and considerably easier to control. Trimarans suffer from the same spatial limitations as catamarans. The addition of an extra hull adds additional space, which is one reason why these multi-hull vessels are some of the best-selling sailboats on the market today.

Sailboat Rig Types

Rigging is another way to distinguish sailboat types. The rig of a sailboat refers to it's mast and sail configuration. Here are the most common types of sailboat rigs and what they're used for.

Sloops are the most common type of sailboat on the water today. A sloop is a simple single-mast rig that usually incorporates a tall triangular mainsail and headsail. The sloop rig is easy to control, fun to sail, and versatile. Sloops are common on racing sailboats as they can sail quite close to the wind. These maneuverable sailboats also have excellent windward performance.

The sloop rig is popular because it works well in almost any situation. That said, other more complex rigs offer finer control and superior performance for some hull types. Additionally, sloops spread their entire sail area over just to canvases, which is less flexible than multi-masted rigs. The sloop is ideal for general-purpose sailing, and it's proven itself inland and offshore.

Sloop Features:

Most popular sailboat rig
Single mast
One mainsail and headsail
Typically Bermuda-rigged
Easy to handle
Great windward performance
Less precise control
Easier to capsize
Requires a tall mast

Suitable Uses:

Offshore cruising
Coastal cruising

Cat (Catboat)

The cat (or catboat) is a single-masted sailboat with a large, single mainsail. Catboats have a thick forward mast, no headsail, and an exceptionally long boom. These vessels are typically gaff-rigged, as this four-edged rig offers greater sail area with a shorter mast. Catboats were popular workboats in New England around the turn of the century, and they have a large following today.

Catboats are typically short and wide, which provides excellent stability in rough coastal conditions. They're hardy and seaworthy vessels, but they're slow and not ideal for offshore use. Catboats are simple and easy to control, as they only have a single gaff sail. Catboats are easy to spot thanks to their forward-mounted mast and enormous mainsail.

Catboat Features:

Far forward-mounted single mast
Large four-sided gaff sail
Short and wide with a large cockpit
Usually between 20 and 30 feet in length
Excellent workboats
Tough and useful design
Great for fishing
Large cockpit and cabin
Not ideal for offshore sailing
Single sail offers less precise control
Slow compared to other rigs
Inland cruising

At first glance, a cutter is difficult to distinguish from a sloop. Both vessels have a single mast located in roughly the same position, but the sail plan is dramatically different. The cutter uses two headsails and often incorporates a large spar that extends from the bow (called a bowsprit).

The additional headsail is called a staysail. A sloop only carries one headsail, which is typically a jib. Cutter headsails have a lower center of gravity which provides superior performance in rough weather. It's more difficult to capsize a cutter, and they offer more precise control than a sloop. Cutters have more complex rigging, which is a disadvantage for some people.

Cutter Features:

Two headsails
Long bowsprit
Similar to sloop
Gaff or Bermuda-rigged
Fast and efficient
Offers precise control
Superior rough-weather performance
More complex than the sloop rig
Harder to handle than simpler rigs

Perhaps the most majestic type of sailboat rig, the schooner is a multi-masted vessel with plenty of history and rugged seaworthiness. The schooner is typically gaff-rigged with short masts and multiple sails. Schooners are fast and powerful vessels with a complex rig. These sailboats have excellent offshore handling characteristics.

Schooners have a minimum of two masts, but some have three or more. The aftermost large sail is the mainsail, and the nearly identical forward sail is called the foresail. Schooners can have one or more headsail, which includes a cutter-style staysail. Some schooners have an additional smaller sale aft of the mainsail called the mizzen.

Schooner Features:

At least two masts
Usually gaff-rigged
One or more headsails
Excellent offshore handling
Precise control
Numerous sail options (headsails, topsails, mizzen)
Fast and powerful
Complex and labor-intensive rig
Difficult to adjust rig single-handed
Offshore fishing

Picture a ketch as a sloop or a cutter with an extra mast behind the mainsail. These vessels are seaworthy, powerful, excellent for offshore cruising. A ketch is similar to a yawl, except its larger mizzen doesn't hang off the stern. The ketch is either gaff or Bermuda-rigged.

Ketch-rigged sailboats have smaller sails, and thus, shorter masts. This makes them more durable and controllable in rough weather. The mizzen can help the boat steer itself, which is advantageous on offshore voyages. A ketch is likely slower than a sloop or a cutter, which means you aren't likely to find one winning a race.

Ketch Features:

Headsail (or headsails), mainsail, and mizzen
Mizzen doesn't extend past the rudder post
Good offshore handling
Controllable and mild
Shorter and stronger masts
Easy self-steering
Slower than sloops and cutters
Less common on the used market

A dinghy is a general term for a small sailboat of fewer than 28 feet overall. Dinghys are often dual-power boats, which means they usually have oars or a small outboard in addition to a sail. These small boats are open-top and only suitable for cruising in protected waters. Many larger sailboats have a deployable dinghy on board to get to shore when at anchor.

Dinghy Features:

One or two people maximum capacity
Easy to sail
Works with oars, sails, or an outboard
Great auxiliary boat
Small and exposed
Not suitable for offshore use
Going from anchor to shore
Protected recreational sailing (lakes, rivers, and harbors)

Best Sailboat Type for Stability

Stability is a factor that varies widely between sailboat types. There are different types of stability, and some sailors prefer one over another. For initial stability, the trimaran wins with little contest. This is because these vessels have a very high beam-to-length ratio, which makes them much less prone to rolling. Next up is the catamaran, which enjoys the same benefit from a wide beam but lacks the additional support of a center hull section.

It's clear that in most conditions, multihull vessels have the greatest stability. But what about in rough weather? And what about capsizing? Multihull sailboats are impossible to right after a knockdown. This is where full-keel monohull sailboats excel.

Traditional vessels with deep displacement keels are the safest and most stable in rough weather. The shape, depth, and weight of their keels keep them from knocking over and rolling excessively. In many cases, these sailboats will suffer a dismasting long before a knockdown. The primary disadvantage of deep-keeled sailboats is their tendency to heel excessively. This characteristic isn't hazardous, though it can make novice sailors nervous and reduce cabin comfort while underway.

Best Sailboat Type for Offshore Cruising

The best sailboat type for offshore cruising is the schooner. These graceful aid robust vessels have proven themselves over centuries as durable and capable vessels. They typically use deep displacement keels, which makes them stable in rough weather and easy to keep on course.

That said, the full answer isn't quite so simple. Modern multihull designs are an attractive option, and they have also proven to be strong and safe designs. Multihull sailboats are an increasingly popular option for offshore sailors, and they offer comfort that was previously unknown in the sailing community.

Many sailors cross oceans in basic Bermuda-rigged monohulls and take full advantage of a fin-keel design speed. At the end of the day, the best offshore cruising sailboat is whatever you are comfortable handling and living aboard. There are physical limits to all sailboat designs, though almost any vessel can make it across an ocean if piloted by a competent skipper and crew.

Best Sailboat Type for Racing The modern lightweight Bermuda-rigged sailboat is the king of the regatta. When designed with the right kind of hull, these vessels are some of the fastest sailboats ever developed. Many boats constructed between the 1970s and today incorporate these design features due to their favorable coastal and inland handling characteristics. Even small sailboats, such as the Cal 20 and the Catalina 22, benefit from this design. These boats are renowned for their speed and handling characteristics.

I've personally had thousands of questions about sailing and sailboats over the years. As I learn and experience sailing, and the community, I share the answers that work and make sense to me, here on Life of Sailing.

by this author

Learn About Sailboats

Most Recent

What Does "Sailing By The Lee" Mean?

October 3, 2023

The Best Sailing Schools And Programs: Reviews & Ratings

September 26, 2023

Important Legal Info

Lifeofsailing.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon. This site also participates in other affiliate programs and is compensated for referring traffic and business to these companies.

Affordable Sailboats You Can Build at Home

September 13, 2023

Best Small Sailboat Ornaments

September 12, 2023

Discover the Magic of Hydrofoil Sailboats

December 11, 2023

Best Liveaboard Catamaran Sailboats

December 28, 2023

Can a Novice Sail Around the World?

Elizabeth O'Malley

Best Electric Outboard Motors | Life of Sailing

4 Best Electric Outboard Motors

How Long Did It Take The Vikings To Sail To England?

10 Best Sailboat Brands | Life of Sailing

10 Best Sailboat Brands (And Why)

December 20, 2023

7 Best Places To Liveaboard A Sailboat

Get the best sailing content.

How Sails Work: Understanding the Basics

Table of Contents

Last Updated on September 1, 2023 by Boatsetter Team

Sailing is all about physics and geometry but don’t worry, it’s not too hard to learn. Once the theory is down, it’s all a matter of practice. Let’s look at what sails are and how they work.

Book a sailboat rental & set out on your next expedition

Aerodynamics, hydrodynamics & modern sails

Sails work like airplane wings, except they’re vertical rather than horizontal. As the wind hits the front of a curved sail, it splits, passing on both the downwind (leeward) side and upwind (windward) side.

The leeward wind travels farther due to the curvature of the sail and creates a low-pressure area while the windward wind travels a shorter distance and reaches the aft end faster – together, they create aerodynamic lift that “pulls” the boat forward .

The keel or centerboard in the water below the hull prevents the boat from being pushed sideways. With the lift of the sails and the lateral push or hydrodynamics of the keel, the boat is propelled forward. Where the wind concentrates force in the sails is called the center of effort, while the keel below is called the center of lateral resistance.

Most modern sailboats have a forward (or headsail) and a mainsail. The headsail may be called a genoa, jib, or staysail (different sizes) and is attached at the top of the mast and leads down at an angle to the bow . It’s controlled by lines called sheets. The mainsail is supported by the mast and is attached at the bottom to a lateral spar called the boom.

Parts of a sail

Sails come in various shapes, but for our purposes, we will focus on modern, triangular sails. The top of the sail is called the head , and the bottom is the foot. The forward end of the foot is the tack, and the aft end is the clew. The forward edge of the sail is the luff, and the aft end is the leach.

Telltales or short strands of yarn are often attached near the leading edge of a sail to help with sail trim. The shape of the sail is ideal when the strands on both sides are streaming back at the same level, which indicates that wind is moving evenly along both sides of the sail.

Points of sail

A boat cannot sail directly into the wind– instead, it sails at an angle to the true breeze. Close hauled is roughly 45 degrees off the wind, close reach is 60 degrees, beam reach is at 90 degrees, and a broad reach is approximately 150 degrees off the wind.

When moving directly or dead downwind, a boat is said to be running, and when the bow is pointed into the wind, that’s called being in irons. A boat cannot sail in irons and can be hard to control when running. When sails begin to luff at the leading edge, the boat is trying to sail too close to the wind and will stall.

Tacking and jibing (gybing)

A boat changes direction by either tacking or jibing. Sailing upwind, a boat tacks when the bow passes through the eye of the wind until the boat is sailing on the opposite side or “tack” creating a zig-zag course. When sailing downwind, the boat jibes when passing the stern through the wind.

Turning upwind is called heading up and turning away, or downwind is falling off. When the wind passes over the starboard rail first, you’re on a starboard tack and vice versa.

Pro Tip: You can learn how to sail without owning a sailboat. Find a sailboat rental near you , then book! You can save that boat listing and book again to continue practicing.

Sail shape & angle

Boats sail in true wind (the wind that is actually blowing at a given speed and angle) by they’re actually responding to the apparent wind (the angle and speed of the breeze that is felt once the boat is moving). The wind always changes speed and angle, so sails must be adjusted or trimmed in response to the boat to maintain optimal speed.

When sailing upwind, the sails are sheeted in (made flatter by pulling in the sheet lines) to create better foils and greater lift or pull. When sailing downwind, sails are usually loosened or let out to create a “belly” and adjusted to be as perpendicular to the angle of the wind as possible.

Sheeting in (bringing the sails closer to the centerline) enables the boat to point higher (sail closer to the true wind) while easing out (loosening the aft end of the sail) creates more power when the wind is aft like around the beam or broad reach.

A boat is more likely to heel when sheeted in and sailing upwind. Excessive healing doesn’t mean the boat is traveling faster. In fact, it may just be getting overpowered and becoming less efficient than if the sails were trimmed properly.

In high winds, shorten or reef sails so the boat doesn’t become overpowered and potentially dangerous. Reefing is done at the tack and clue or the forward and aft parts of the foot of the sail. There may be 1-3 pre-rigged reefing points controlled by reefing lines, so the sails can be made as small as necessary to keep the boat from heeling too far.

Easy to learn

Trimming sails takes time to master; let sails out until they luff or flap, and then sheet in until you feel the boat pick up speed. Smaller boats react quickly to each adjustment and are better for new sailors to learn on than large boats that take a minute to speed up or slow down. Once you’ve mastered the theory, you may spend years perfecting your sailing skills.

Boatsetter is a unique boat-sharing platform that gives everyone— whether you own a boat or you’re just renting — the chance to experience life on the water. You can list a boat , book a boat , or make money as a captain .

List. Rent. Earn— Only at Boatsetter

Zuzana Prochazka is an award-winning freelance journalist and photographer with regular contributions to more than a dozen sailing and powerboating magazines and online publications including Southern Boating, SEA, Latitudes & Attitudes and SAIL. She is SAIL magazines Charter Editor and the Executive Director of Boating Writers International. Zuzana serves as judge for SAIL’s Best Boats awards and for Europe’s Best of Boats in Berlin.

A USCG 100 Ton Master, Zuzana founded and manages a flotilla charter organization called Zescapes that takes guests adventure sailing at destinations worldwide.

Zuzana has lived in Europe, Africa and the United States and has traveled extensively in South America, the islands of the South Pacific and Mexico.

Browse by experience

Explore articles

St. Petersburg Water Activities

Ten Holiday Gifts Every Boater Will Love

Offshore Fishing in Florida’s Nature Coast for Grouper and Snapper

5 Tips for Holiday Charters & Handling New Renters

All You Need to Know: Explaining the Different Types of Sailboats

Sailboats are a type of watercraft that are powered by the wind. They come in a variety of shapes and sizes, each with its unique characteristics and features. Understanding the different types of sailboats and their uses can be helpful for those who are interested in sailing or looking to purchase a sailboat.

Several factors determine the types of sailboats, including the hull type , keel type , mast configuration, and sails and rigging . The hull is the boat’s body and can be either a monohull, catamaran , or trimaran .

The keel is the underwater part of the hull that provides stability and can be either a fin keel, wing keel, bilge keel, daggerboard, or centerboard. The mast configuration and sails determine how the boat is powered, and can be a sloop, fractional rig sloop, ketch, schooner, yawl, cutter, or cat.

Types of Sailboats

Sailboats come in many different shapes and sizes, each designed for a specific purpose. Here are the most common types of sailboats:

Cruising Sailboats

Cruising sailboats are designed for long-distance sailing and living aboard. They typically have a spacious interior with a galley, head, and sleeping quarters. They also have a large fuel and water capacity to allow for extended time at sea. Cruising sailboats come in many different sizes, from small pocket cruisers to large bluewater yachts.

Racing Sailboats

Racing sailboats are designed for speed and agility. They typically have a lightweight hull and a tall mast with a large sail area. Racing sailboats come in many classes , from dinghies to large offshore racing yachts. They are designed to be sailed by a skilled crew and require a high level of skill and experience to handle.

Daysailers are designed for short trips and day sailing. They typically have a simple interior with minimal accommodations. Daysailers come in many different sizes, from small dinghies to larger keelboats. They are easy to handle and are a great choice for beginners or for those who want to enjoy a day on the water without the hassle of a larger boat.

Catamarans are sailboats with two hulls. They are designed for stability and speed and are often used for cruising or racing. Catamarans have a spacious interior and a large deck area, making them a popular choice for those who want to live aboard or entertain guests. They are also popular for chartering and can be found in many popular sailing destinations around the world.

Trimarans are sailboats with three hulls. They are designed for speed and stability and are often used for racing or long-distance cruising. Trimarans have a narrow hull and a large sail area, making them incredibly fast and agile on the water. They are also popular for their spacious interior and large deck area, making them a great choice for those who want to live aboard or entertain guests.

Sailboat Hull Types

When it comes to sailboats, there are two main categories of hull types: monohull and multihull. Each has its unique characteristics and advantages.

Maxi 1300 Performance Bulb Keel Cruising Sailboats

Monohull Sailboats

Monohull sailboats are the most common type of sailboat. They have a single hull, and the hull is typically long and narrow, which makes them more efficient when sailing upwind. Monohulls come in a variety of styles, including:

Flat-bottom vessels
Fin-keel racers
Bulb and bilge keel cruisers
Heavy semi-displacement sailboats
Dense full-keel displacement cruisers

Each of these styles has its advantages and disadvantages. For example, flat-bottom vessels are the most stable, but they don’t work well in deep waters. Fin-keel racers are designed for speed and performance but may not be as comfortable for long-term cruising.

Multihull Sailboats

Multihull sailboats have two or more hulls. The most common types of multihulls are catamarans and trimarans. Multihulls have several advantages over monohulls, including:

More stability
Better performance in light winds

Catamarans have two hulls, which are connected by a deck. They are known for their stability and spaciousness. Trimarans have three hulls, which make them even more stable and faster than catamarans. However, they are not as spacious as catamarans.

Sailboat Rigging Types

When it comes to sailboat rigging types, there are several options to choose from. Each type of rig has its advantages and disadvantages, and choosing the right one will depend on a variety of factors, including the type of sailing you plan to do and the size of your boat . Some of the most common sailboat rigging types include:

The sloop rig is one of the most popular sailboat rigging types and is commonly used on boats ranging in size from small dinghies to large cruisers. It consists of a single mast with a mainsail and a jib or genoa. The mainsail is typically a triangular shape, while the jib or genoa is a smaller sail that is used to control the boat’s direction.

The cutter rig is similar to the sloop rig but with an additional headsail. This makes it a popular choice for sailors who want more control over their boat’s speed and direction. The mainsail is still triangular, but the headsail is typically smaller than the jib or genoa used in a sloop rig.

The ketch rig is a two-masted sailboat rigging type that is commonly used on larger boats. It consists of a main mast and a smaller mizzen mast located aft of the cockpit. The mainsail is typically triangular, while the mizzen sail is smaller and located behind the cockpit. The ketch rig is known for its versatility and is often used for long-distance cruising.

The yawl rig is similar to the ketch rig but with a smaller mizzen mast located further aft. This makes it a popular choice for sailors who want more control over their boat’s direction, especially in heavy winds. The yawl rig is also known for its ability to sail close to the wind, making it a popular choice for racing sailors.

Sailboat Sails

Several types of sails are commonly used on sailboats . Each sail has a specific purpose and is designed to work in different wind conditions. The main types of sails include mainsails, jibs, genoas, and spinnakers.

The mainsail is the largest sail on a sailboat and is typically located behind the mast. It is attached to the mast and boom and is used to capture the wind and propel the boat forward. The mainsail is the most important sail on the boat and is used in a wide range of wind conditions.

The mainsail can be adjusted in several ways to optimize its performance. The sail can be reefed, or reduced in size, to reduce the amount of sail exposed to the wind in high winds. The sail can also be twisted to adjust the shape of the sail and improve its performance in different wind conditions.

The jib is a smaller sail that is located in front of the mast. It is attached to the mast and forestay and is used to help balance the boat and improve its performance in light wind conditions. The jib is typically used in conjunction with the mainsail and can be adjusted to optimize its performance.

There are several types of jibs, including the working jib, the genoa jib, and the storm jib. The working jib is the most common type of jib and is used in moderate wind conditions. The genoa jib is a larger jib that is used in light wind conditions, while the storm jib is a smaller jib that is used in high wind conditions.

The genoa is a large jib that is used in light wind conditions. It is similar to the jib but is larger and overlaps the mainsail. The Genoa is attached to the mast and forestay and is used to capture as much wind as possible to propel the boat forward.

The Genoa is typically used in conjunction with the mainsail and can be adjusted to optimize its performance. It can be furled, or rolled up when not in use to reduce wind resistance and improve the boat’s performance.

The spinnaker is a large, balloon-shaped sail that is used for downwind sailing. It is typically used in light wind conditions and is attached to a spinnaker pole to keep it away from the boat’s mast and sails.

The spinnaker is used to capture as much wind as possible and propel the boat forward. It is typically used in conjunction with the mainsail and jib and can be adjusted to optimize its performance.

What factors determine the types of sailboats?

The factors that determine the types of sailboats include hull type, keel type, mast configuration, and sails and rigging.

What are the two main categories of sailboat hull types?

The two main categories of sailboat hull types are monohull and multihull.

What are some common sailboat rigging types?

Common sailboat rigging types include sloop rig, cutter rig, ketch rig, and yawl rig.

What are the main types of sails used on sailboats?

The main types of sails used on sailboats include mainsails, jibs, genoas, and spinnakers.

What are the differences between a catamaran and a trimaran?

A catamaran has two hulls connected by a deck, while a trimaran has three hulls. Trimarans are generally more stable and faster than catamarans, but they are not as spacious.

Recent Posts

Sustainable and Luxurious: Discovering Split’s Yachting Paradise – April 26, 2024
MarineTraffic vs VesselFinder: Which Is Better Vessel Tracking Service? – February 14, 2024
Port Costs: A Comprehensive Guide to Port Dues and Fees for Cargo Ships – February 12, 2024

About the author

I worked as an officer in the deck department on various types of vessels, including oil and chemical tankers, LPG carriers, and even reefer and TSHD in the early years. Currently employed as Marine Surveyor carrying cargo, draft, bunker, and warranty survey.

Latest posts

Marine Satellite Internet: How Ships Keep Connected

Some boaters take leisurely trips to the lake while others venture into the ocean, far removed from the rest of civilization. Thankfully, marine satellite internet helps ships stay connected.

What to Wear on a Boat

Sailing on a ship requires extensive preparation. In addition to understanding its components and how to operate it, people must also know what to wear on a boat.

What Happens if a Ship Loses Power?

A power outage is among the worst issues for maritime professionals. What happens if a ship loses power?

My Cruiser Life Magazine

Sailboat Types: Full-Guide

For generations, sailing has been a mode of essential transportation, a rewarding hobby, an active and competitive sport, and a lifestyle. Sailing appeals to all, and there are dozens and dozens of types of sailboats.

Small sailboats are perfect for kids to sail on, and massive sailboats are used to cross oceans in style. In between, there are daysailers, racers, and cruisers.

What Does a Sailboat Look Like?

Small Sailboats

Cruising boats, cruising catamarans, cruising trimarans, full keel boats, fin keel boats, centerboard keel.

Hydrofoil Sailboats

A Purpose for Every Type of Sailboat

Faqs (frequently asked questions).

What Are Sailboat Types?

Sailboats are boats that are propelled by the wind. Sailboats use wind power instead of a motor or oars to move the boat. It should be noted, though, that nearly all modern sailboats have a motor as well. It comes in handy when docking in tight marinas and if the wind dies!

A sailboat has one, two, or three hulls. It has at least one mast, or tall vertical spar, that holds up one or more sails. The sails harness the power of the wind to move the boat forward.

To get started, here are some sailing boat types and terms to give you an idea of the sorts of boats that are out there.

Dinghies — a small open boat, usually for only one or two people
Daysailors — boats designed to go out for a day trip
Cruising Sailboats — boats designed to travel long distances that have accommodations for their crew to live aboard a long term
Sloop — the most common type of sailboat, with one mast and two sails (a jib and a mainsail)
Ketch, yawl, or schooner — types of sailboats with two or more masts
Monohull — a boat with only one hull
Catamaran — a boat with two equal-sized hulls in the water that are connected together by a bridge deck
Trimaran — a boat with three hulls in the water, the center of which is much larger than the outer two

What Does a Sailboat Look Like?

There are many different types of sailboats, so they look a little different from each other. The basics, however, are the same.

Each sailboat has at least one hull that sits in the water. Part of the hull is visible above the waterline. Part of the sailboat hull sits below the waterline.

The part beneath the waterline might be relatively small, or it can be quite large. The rudder, the mechanism used to steer the boat, is also underwater.

The cockpit is where the helmsperson sits and steers the boat. On small boats, the cockpit takes up the entire boat. Cruising boats have interior accommodations as well as a safe cockpit.

Sailboats have at least one mast and at least one mainsail. As you get to know the different types of sailboats, you’ll see many different hull and sail configurations.

Different Types of Sail Boats

Sailboats come in all types of sailboat shapes and sailboat sizes . Sailboats can be classified by their hull shape, size, or sail plan. The sail plan is how many sails they carry on how many masts.

Hull shapes include monohulls, catamarans, trimarans, and sailing hydrofoils. A monohull has just one hull, a catamaran has two hulls, a trimaran has three hulls, and a hydrofoil lifts out of the water.

Sizes range from eight-foot sailboats to megayachts that are hundreds of feet long. Some sailboats are so small they are only suitable for one child who wants to go skimming across the lake. The largest pure sailing yacht in the world is the Black Pearl at 350 feet long (106.7 meters) long. Visit our Yacht vs Sailboat guide for a more definitive difference between the two and their sizes.

Sailboats also have different sail configurations or sail plans. For example, a sailboat with just one big sail on a forward-mounted mast is called a catboat. A boat with dozens of different sails on three masts is called a three-mast schooner.

Small sailboats are extremely popular and offer a lot of fun to the young and old. Most of the time, these boats are just used for daytime use in pleasant weather conditions. Kids often learn to sail in small monohull sailboats. Families might go for a picnic in a Hobie catamaran.

Yacht club members might race their 16-foot daysailors, while adventurous souls might take their 19-ft weekender and anchor in a calm cove for the weekend.

What is a Small Sailboat Called?

Small sailboats have different names, depending on the type of sailboat and the number of sail boat hulls. For example, the boat might be a monohull dinghy, small catboat, small catamaran, or daysailor.

Additionally, like every car on the road, every boat on the water is identified by its make and model. In small boats that are commonly raced, a certain make and model may set up a class of racing boats. Class racing means that all of the boats are identical, so the race is based solely on the skills of the skippers.

Sailing Dinghies

Kids and adults often learn to sail on sailing dinghies. Sailing dinghies can be as small as eight feet long. This small size makes it easy for kids to handle.

Some common sailing dinghies are Optis, Lasers, and Sunfish.

This size sailboat is also functional. They can be used to ferry sailors from their larger anchored boats to shore. The small size also helps sailors easily store their dinghy on larger boats. The word dinghy is often used to refer to any small boat used as a tender for a larger vessel, even if the tender is a motorboat.

Cat Rig Boats

A cat rig boat, or cat boat, is a type of sailboat that usually just has one large mainsail and a forward-mounted mast. Many smaller dinghies and training boats are catboats. A catboat has a free-standing mast with no standing rigging.

Small Catamarans

A catamaran is a boat with two hulls. The Hobie brand is synonymous with small catamarans, which are popular with families looking for a fun hobby. Hobie Cats are seen on the sand at beach resorts all over the world—they’re safe, fun, and fast.

Catamarans are faster than monohulls, and these boats are fun to race. Small catamarans are often used by families that live on the waterfront. Their lightweight makes them easy to drag to the waterfront and launch.

Small catamarans are also popular on beaches. Many beach resorts offer Hobie cats for rent. Small catamarans are between 12-20 feet in length. The hulls are joined only with spars and netting, so these fast and light open boats are not set up to carry a lot of people or supplies.

Daysailors are the ultimate fun boat. As the name implies, this type of sailing boat is used for day sailing. These boats are usually between 12 to 20 feet long. Some use these smaller boats for racing or overnight camping, but most sailors use daysailors for a leisurely sail.

Small Sailboats with Cabins

While most small sailboats just have a large open cockpit, several small yacht types have cabins. These cabins offer a chance for sailors to use a porta-potty or get out of the sun. Some small sailboats even have sleeping accommodations for overnight stays.

An excellent example of this is the Cape Dory Typhoon Weekender. This small sailboat is known as “America’s Littlest Yacht.” Down below, there are two small bunks for sleeping and enough space to have a small stove and a porta-potty. Most owners don’t stay aboard long-term, but the cabin is a useful place to stow items while sailing or to hide during a rainstorm.

Cruising boats are boats that are capable of traveling long distances. Cruising boats have sleeping accommodations, cooking facilities, and bathroom facilities. These boats are like RVs for the waterway.

Cruising boats offer sailors the chance to live on their boats while sailing. Like RVs, cruising sailboats travel to different ports of call. Cruising sailboats are one of the more popular types of sailing boat. They offer adventurous sailors the chance to enjoy sailing as a sport while seeing new things.

Cruising boats are usually 30 to 50 feet long. Most cruising couples prefer a boat that is around 40 feet long since this provides enough space to live comfortably and enough storage space for all of their gear.

Monohulls are very popular cruising boats. These boats offer good storage, are safe, and are easy for a couple to handle together. Monohulls have different types of sail configurations.

Cruising Bermuda Rigged Sloops

Most monohulls are Bermuda rig sloops. This sail plan features one mast with a mainsail and a headsail. Bermuda rig sloops are easy to single-hand and very versatile. How many sails does a sloop have? A Bermuda sloop flies two sails at a time, which are the mainsail and a headsail.

However, the boat might have other sails onboard. For example, the captain might take down the jib in light winds and use a bigger genoa to capture more wind power. During a downwind sail with light winds, the captain might rig a large spinnaker, which looks like a huge kite, to keep sailing even in little wind.

Even within the sloop category, there are many variations in the design. A masthead sloop is one whose forestay (headsail) goes all the way to the top of the mast. In contrast, a fractional sloop’s forestay connects at some point lower. So a 3/4 fractional rig has a headsail that only goes up three-quarters of the way to the top.

Riggers and boat designers have a lot of tools in their toolbox from which they can make a boat faster or more user-friendly. The type of rigging and sail plan a boat is equipped with offers it performance improvements as well as functionality.

Cruising Cutter

A cutter is a sailboat with one mast, one mainsail, and two sails forward of the mast. The sail at the front of the boat is the jib, genoa, or yankee depending on its size and cut. The next sail in, the inner headsail, is called the staysail. Island Packets are popular boats with this sail plan.

Cutters are popular choices as cruising and bluewater cruiser boats because the staysail provides the skipper with many different sail options. They could fly all three sails fully, or they could fly a small partial mainsail and just the staysail for heavy winds.

Cruising Ketch With Mizzen Sail

Some cruising monohulls are ketches. A ketch can be easily identified by its two masts. The forward mast is the main mast with a mainsail. The aft mizzen mast is shorter and has a mizzen sail. This sail plan can make it easier to carry a big sail area and configure the sails for various sailing conditions.

A boat with more than one mast is called a split rig because the rig is split between two shorter masts instead of all mounted on one tall one. The advantage of a split rig is that there are more sails, each of which is smaller. That makes them easier to handle, and important consideration when you are sailing alone or with only one other person.

Cruising Yawl

A yawl is similar to a ketch and has two masts. However, the mizzen mast on a yawl is aft of the rudder post, whereas it is forward of the rudder post on a ketch. This mizzen mast location is even further back than a ketch’s. Yawls are one of the less popular types of sailboats. However, like the ketch, they offer diverse sail options and can keep sailing in many different types of weather.

On both ketches and yawls, the mizzen mast is shorter than the main mast. If the two masts are of equal height, or the forward mast is shorter, then you are looking at a schooner.

Cruising catamarans are one of the most popular classes of sailboats right now. This type of sailing boat has two hulls and offers sailors speed, space, and comfort. A cruising catamaran is usually between 40 and 60 feet long and 20 to 30 feet wide. The additional width offers cruise sailors huge amounts of space.

Cruising catamarans have excellent storage space and ample living accommodations if you intend to living on a boat . These boats are popular with couples and families and are often used to sail around the world on circumnavigations.

Cruising catamarans are usually fractional sloop rigs. They have one mast, a large mainsail, and a jib or genoa. In general, these boats are designed to be easy to sail and minimize complications.

Trimarans are a type of sailboat with three hulls. Trimarans are known to be fast and are popular with racing sailors. However, they are also gaining popularity as cruising boats. These boats usually have fewer accommodations than cruising monohulls and catamarans. However, more modern trimarans like the Neel Trimaran have luxurious living spaces.

Types of Keel

Another way to classify the different types of sailing boats is by looking at the boat’s keel type. You can easily get an idea of different keel designs by walking around a boatyard. When a sailboat is in the water, it is hard to tell the shape of its keel.

The keel is the bottom part of the hull and is underwater. The keel is structurally essential. The keel’s weight helps the boat sail evenly and uprightly. The force created by the water moving over the keel counteracts the effects of the wind on the sails.

So a keel does two jobs for a sailboat. First, it provides a force that allows a sailboat to sail into the wind. Second, it provides stability. If storm-force weather conditions cause a monohull boat to roll, the weight in the keel will help the boat right itself.

Many older cruising boats had full keels. The keel shape runs the entire length of the boat. A full-keel boat is strong and easy to manufacture. Full-keel boats often have deeper drafts. The boat’s draft refers to the amount of water it needs to float. Full-keel boats can’t go into the shallow anchorages that catamarans or swing-keel boats can access.

Captains often report that full-keel boats are harder to maneuver in tight places such as marinas. Full-keel boats lack quick maneuverability. They have a reputation for being slower than more modern designs, but they make up for this by providing a very comfortable and safe ride in rough weather.

A boat with a fin keel has a smaller underwater profile than a boat with a full keel. This smaller keel resembles a fish fin. Captains find fin keel boats easier to maneuver. Fin keels use their shape to create very effective forces underwater. That makes them very good at countering the forces on the sails, meaning that fin keels sail upwind very well.

A boat with a bulb keel has a torpedo-shaped bulb on the bottom of a fin keel. Bulb keels offer improved stability. Bulb keels have shallower keels than a fin keel boat. The bulb also lowers the center of gravity in the boat, making it more stable overall.

A wing keel features a keel with a small wing on either side of the keel. Viewed from above, the keel looks like it has a set of small airplane wings.

Similar to a bulb keel, wing keel boats often have a shallower draft than fin-keel boats. However, the additional shape causes drag and can reduce sailing performance in some circumstances.

A centerboard is common on small daysailors that are launched and retrieved from trailers. Deep keels make getting those boats in and out of the water difficult. By chopping off the keel, you can make a sailboat as easy to launch as a powerboat.

Related: Best Trailerable Sailboats

But of course, a sailboat needs to have a keel. A centerboard is a simple swinging fin keel that can be raised or lowered. This provides some excellent benefits if the sailor on board likes to explore areas with shallow water.

Many bigger boats have centerboards, too. A boat with a centerboard can be seen as the best of both worlds. A centerboard boat has a fixed shallow draft keel. However, the captain can deploy the centerboard when sailing in deeper waters. The centerboard adds depth to the keel and offers increased stability and performance.

A modification of the centerboard is the swing keel — a ballasted keel that can be retracted like a centerboard . These are rare. They’re used on large cruising boats where the crews want the option of accessing shallow waters. In England, this type of boat is used and can be dried out when the tide goes out.

Racing Sailboats

Yacht racing is a popular sailing sport. It’s a great way to get out on the water while competing. In fact, racing is a great way for sailors to hone their sailing skills. Sailors have to pay close attention to weather conditions and manage their sails effectively to maximize their speed.

Sailors can race any boat with sails. Kids race sailing dinghies against each other. Club racers sail daysailors or catboats. Catamarans and trimarans are also popular race boats. Several classes of boat races in the Summer Olympics.

Hydrofoil Sailboats

A hydrofoil is a unique and modern type of racing sailboat. A hydrofoil can be a monohull, catamaran, or trimaran. A hydrofoil has wing-like foils on the hull’s underside.

As the sailboat speeds up, the hydrofoils lift the hull out of the water, and the hydrofoil sailboat almost appears to be flying above the water.

Because the hull is now out of the water, drag, and resistance are minimal, and the sailboat can sail even faster. For example, a dinghy that usually goes four knots can accelerate to 12 knots when fitted with a hydrofoil.

Most hydrofoil sailboats are catamarans and trimarans. The added width of these multihull sailboats gives the hydrofoil sailboat more stability.

Traditional Sailboats

Traditional sailboats are the type of sailboats used to transport people and goods before modern transportation options were available. Before the railway, cars, and airplanes, a tall ship sailboat was used to ship cargo and people across oceans and from port to port.

A gaff rig refers to the gaff, which is the upper spar on a square-shaped sail. Gaff rigs can be used with any mast configuration, but this feature is usually seen on traditional boats like a catboat, tall ship, or schooner.

A schooner has at least two masts. They are different from other mast configuration designs with two spars in that both masts are equal in height, or the forward mast is shorter. Schooners are faster than most traditional boats and were often used to transport perishable goods such as fruit.

Schooners were also popular race boats in the early 20th century. For example, first America’s Cup races were won by schooners.

Today, schooners are usually used as charters for vacations or youth sail training programs. But there are a few cruising boats out there that feature schooner rigs.

Any way you divvy it up, there are tons of different types of sailboats out there. With a little research and a little looking, you’re sure to find one that suits your style and boating plans.

What are the classes of sailboats?

Sailboat styles can be classified by hull type, use, or sail plan. The types of sailboat hulls include monohulls, catamarans, and trimarans. You can also categorize the kinds of sailboats by their use. For example, sailors use their boats for daysailing, cruising, and racing. Finally, different kinds of sailboats have different sail plans. A sailboat might be a sloop, ketch, yawl, catboat, or schooner. The term “classes” has a particular meaning in sailing, however. Class racing is the competitive racing between boats of the same make and model—boats of the same “class” or of “one design.” There are hundreds of different classes of sailboats out there. Some of the most popular classes include the Laser and Sunfish classes.

What is a small 2 person sailboat called?

A small two-person sailboat is a dinghy. These small boats are fun to sail on protected waters. Many kids learn to sail in a sailing dinghy. There are dozens of makes and models of sailing dinghies available, some are used in Olympic sailing racing while others are just rowboats with sail rigs attached.

Matt has been boating around Florida for over 25 years in everything from small powerboats to large cruising catamarans. He currently lives aboard a 38-foot Cabo Rico sailboat with his wife Lucy and adventure dog Chelsea. Together, they cruise between winters in The Bahamas and summers in the Chesapeake Bay.

Your email address will not be published. Required fields are marked *

Save my name, email, and website in this browser for the next time I comment.

Students from Belle Isle program build their own boat. Now they look to sail it

Eight middle school students returned to Belle Isle this summer for another year of sailing lessons. But a few months ago, before they hit the water, those students learned a new lesson: how to build a boat.

The Detroit Community Sailing Center launched a pilot program this year that gave students an opportunity to learn how to build a sailboat. In May, they completed 80% of the boat's foundation . On Monday, after having a month off from the project, they put the finishing touches on the boat. On Tuesday afternoon, they attempted to sail it.

With their parents and instructors gathered on the dock to watch, the students pulled their sailboat into the water and took turns successfully sailing their boat.

" I'm proud of them," Harry Jones, president of the Detroit Sailing Community Center, said to one of the parents. "They built the boat."

A hands-on workshop

Brother Ari and Eli Boyce, 14 and 13, of Detroit, have sailed with the Detroit Community Sailing Center's Challenge the Wind youth program for three years and welcomed the opportunity to learn how to build a boat.

"The experience was really fun," Eli Boyce said. "It really got easier over time, like learning how to use the tools. And it really helped that it was a really hands-on experience, it wasn't really like they showed you it and they just did it."

Learning a new set of skills can come with challenges.

"The hardest part for me, I think, was when we were cutting and like trying to make the shapes of the boat, it's a lot of back and forth with saws and tools and stuff," Ari Boyce said. "And I think that's the hardest part for me, just like, trying to carve out and get the right shape of the boat and different pieces together and all that."

Eli said he struggled most with conversions.

"The hardest part for me was probably the measuring portion of it because, when we were building the boat, instead of using like normal inches, like feet and stuff, we had to use millimeters and it was a rough change for me," Eli Boyce said.

After learning about the pilot program from an email, Laura Thomas, 47 of Grosse Pointe, thought it would be a great project for her 13-year-old son Logan, who already had some experience in woodworking.

"He really enjoyed making something that was something you could actually use and take out on the water and everything. And that experience of creating something that you can go out and utilize was something he really enjoyed."

Future of the program

Jones said the boat building workshop could be the foundation for a year-round curriculum around sailing, so students aren't just involved in the summer.

"For the past couple of years, we've been looking to expand the educational component, STEM component of our program," Jones said. "And we tried some of the conventional things that other sailing organizations are doing. And it was fine, but it wasn't capturing us emotionally."

The boat building workshop, a partnership between the Detroit Community Sailing Center and the Detroit River Stories Lab out of the University of Michigan, is an attempt to try something more innovative and grow its STEM offerings.

Jones first joined the center in 2011, and has served as director of the program for 10 years. When he first arrived, he said that the program "had fallen in disrepair." People had left the organization and there were only two boats to teach sailing. Today, Detroit Community Sailing has drawn donations in dollars and in vessels. The nonprofit has 40 sailboats, and 100 youths and adults learned how to sail there last year.

The organization has operated out of the Belle Isle Boathouse since 2018. The building now faces an uncertain future , as the state considers demolishing the aging structure in need of renovations. Jones said that the Detroit Community Sailing Center "got some reassurance from the DNR (Department of Natural Resources) that we'll be able to continue to program there regardless of what happens," but understands that all could change, and are looking at other locations should they have to move.

"Hopefully, we won't have to," Jones said, "but we know the reality is that we better have an option if we want to keep the program alive."

'And here we are ...'

In May, the students completed 80% of the boat's foundation as part of the first phase of the project. On Monday, they reunited to begin the second phase. They finalized the boat's design details and installed the last pieces of equipment. Jones said that this boat will be added to the organization's fleet and is looking forward to building more in the future.

The workshop has inspired Ari and Eli to learn more about boats and pursue STEM-based hobbies, and it has brought them closer to their uncle, who has his own motor boat.

"I think that being part of the program helped me understand our uncle's boat a little bit more and like, help talk to him about the boat, and what the boat's doing and what direction the wind is coming from and stuff like that," Eli Boyce said. "It's helped me bond with him, definitely."

Their mother, Kenya Lowe, said that she has seen her children's confidence grow since they first joined Detroit Community Sailing Center in 2021.

"Ari and Eli were very shy but the instructors in the program made them feel comfortable and safe," Lowe, 47, of Farmington Hills, said. "Everyone in the program made the learning experience fun and adventurous. So after that summer, Ari and Eli wanted to come back. And here we are, year (three)."

Looking back, Lowe said that program offered her children, "so much more" than she expected.

"It's absolutely worth it to put your child in this program. You will see so much growth and calmness," Lowe said. "It is such a beautiful feeling to sit outside Belle Isle and watch your child sail a boat on their own. It feels good to know they are confident in their ability to manage a boat."

Eric Guzmán covers youth sports culture at the Free Press as a corps member for Report for America, an initiative of The GroundTruth Project. Make a tax-deductible contribution to support this work at bit.ly/freepRFA .

Contact Eric Guzmán: [email protected]; 313-222-1850. Follow him on X, formerly known as Twitter: @EricGuzman90 .

Find A School
Certifications
North U Sail Trim
Inside Sailing with Peter Isler
Docking Made Easy
Study Quizzes
Bite-sized Lessons
Fun Quizzes
Sailing Challenge

Secrets of Successful Cruising

By: Julie Cappelli Boat Shows , Cruising Tips

“What’s your secret sauce?” is a question I get asked frequently, and not just about the scrumptious creations I whip up in our galley, even in the lumpiest, bumpiest of seas. Usually, curious cruisers are wondering how our transition from being landlubbers to full-time sailors appears to be as smooth as the surface of the sea on your first morning in the doldrums. How did we buy the right boat? How did we take off across the Pacific a mere five months after buying said boat, with very few ripples in our plans, relationship, and lives? And my personal favorite, how the heck did my husband talk me into doing all this crazy cruising nonsense?

That last question is surprisingly the most straightforward to answer, so I’ll start there: my husband didn’t have to talk me into any of this crazy cruising nonsense. We reached the decision together and work hard to remain a team of co-captains rather than competitors trapped on a small sailing vessel with no escape from each other. To cruise successfully and harmoniously as a couple, you too must find balance between work and play, his and her passions, and safely navigate the different learning styles we all have. Which brings me to one of the most important secrets to successful cruising: men and women learn differently. And if you want to set sail for distant horizons, there is a lot of learning to do.

A good place to start is learning to sail, which shouldn’t be a secret but often seems like it is. To this day we credit our exceptional ASA 101 instructor for his relentless patience as we slowly learned the language of sailing, trying not to let the oppressive heat of the Arizona desert melt our brains or enthusiasm. Who knew there was a whole separate language, let alone code of conduct on the water to learn before we were competent enough to skipper a boat of our own?

Once you’ve learned the lingo and the basics of sailing, a great next step is purchasing a sailboat of your own. And I don’t mean the dream boat that you intend to sail away on, or even a racing dinghy. A little trailer sailor you can take out on the weekends or burn all your vacation time using will serve you much better in terms of preparing to voyage to far-flung places around the globe.

Your goal should be to learn this boat inside and out. We spent nearly two years sailing our 1976 Windrose 18, Moxie , nearly every weekend after we decided to go cruising but before we left our jobs. The quick responsiveness of a small, light boat helped us both hone our understanding of boat handling and sail trim without risking safety or sanity on a bigger boat where far greater forces are at play. Being able to take Moxie out whenever we pleased kept us engaged, motivated, and excited, even when our departure date felt forever away. Plus, you’ll earn boat ownership brownie points which could help you qualify for insurance on your next boat. Ladies, as soon as you are comfortable (or perhaps even a little before that), invite your best gal pals out for a spouse-less sail. There is no better way to build your confidence as a skipper which is essential to your success if you’ll be sailing shorthanded.

Can you fix everything on your boat with what’s in your brain and on your boat? If not, that’s your next step, and one of our greatest secrets to successful cruising: true self-sufficiency. When you are cruising in truly remote places or on an offshore passage, you are your own little island of existence in the deep blue sea. And there are responsibilities that come with that awesome reality; to yourself, to your crew, and to your boat. That’s why when you are out in the middle of the ocean your best and only resources are what’s in your brain and what’s on your boat. If you can’t fix or figure out anything that goes awry with the skills you’ve acquired or the resources you’ve stowed in the depths of your lockers, it’s highly likely that your cruise will be cut short and made more challenging by pressing maintenance needs.

It may seem counterintuitive, but investing in high-quality preparatory training is yet another secret that we find continues to pay dividends year after year. At a minimum, you should both take a sail repair workshop, sign up for a hands-on engine service workshop, and attend an electrical troubleshooting class. There simply is no substitute for hands-on learning on how to turn wrenches, properly crimp wire terminations, perfectly tension a halyard, or quickly grind in a reef. Pay close attention to the books and resources used so you can start building your onboard reference library. We find that couples who attend workshops and trainings together tend to enjoy doing boat maintenance more and are better equipped for success when it comes to repair projects. Attending events like these will also help you build your network of other like-minded soon-to-be cruisers, which becomes vitally important as your departure date draws near and the relative comfort of land life tightens its grip on your seafaring spirit.

Be sure to leave room on your calendar and in your budget to complete a liveaboard ocean sail training course that’s at least one week long. Choose an expedition-style course that teaches both traditional and electronic navigation and includes watch standing, sailing at night, and shorthanded man overboard retrieval. Many of our students wish they had prioritized this earlier in the process of preparing to go cruising, so schedule this well before you cast off the docklines for your grand adventure, and ideally before you purchase your cruising boat. It will give you a taste of what ocean voyaging is really like, help you build good boatkeeping habits, and you’ll start to learn what attributes you truly need versus want in your cruising boat.

Are you sensing a theme here? There is no better way to set yourself up for success than by spending time on boats fiddling with sail trim, enacting repairs, and learning how to cook your favorite meals in a galley that rarely stays still. You’ve got to get out there and just do it, but in an environment that allows room for growth and development. Make it your mission to return home with a solid foundation in ocean sailing and seamanship plus more salty souls to add to your cruising network.

You can’t go wrong by focusing on practical preparation, which is probably one of the best-kept secrets of cruising prep. The sooner and more often you work on becoming a self-reliant sailor, the better you will be equipped to tackle the challenges of extended cruising and boat ownership.

The timeless mantra of keeping it simple rings true for all successful long-term cruisers. Keep your boat and its systems as simple as you can. Endeavor to keep the remnants of your land life simple too, but always leave yourself a means to return when you need to. Whether it be budgeting for breaks ashore, maintaining a part-time residence you can return to, or just a nest egg reserved for when the time to plant roots again comes. It takes a lot of effort to achieve your cruising goals, and you deserve to enjoy the fruits of your hard work. Keeping it all simple and giving yourself an “out” will help you relax and appreciate the cruising life even more. Hopefully with a smile and frosty beverage in hand!

There are of course many more ingredients to create your personal recipe for successful cruising, such as identifying your individual cruising goals, selecting the right boat to match your agreed upon goals, and keeping the promise you made to yourself to actually GO.

We’ll be sharing loads more of our best secrets for successful cruising during our three-hour American Sailing Seminar at the Annapolis Boat Show on October 11 from 9am-12pm. Hope to see you there!

Learn From The Experts During This American Sailing Seminar

SECRETS OF SUCCESSFUL CRUISING

HOSTED BY GIO & JULIE CAPPELLI

Pelagic Blue Cruising Services, Owners

✓ Expert Sailors and Instructors

✓ Diverse Expertise

ANNAPOLIS, MD

FRI, OCT 11, 2024

For cruisers and aspiring cruisers intrigued by the secrets to setting sail with confidence and joy, this live seminar will address and navigate the challenges at sea, covering coastal and offshore passages, self-sufficiency in boat maintenance, and relationship dynamics with your crewmate(s).

2024-10-11-asbs-seminar-secrets-to-successful-cruising-main-800×800

Learn To Sail
Mobile Apps
Online Courses
Upcoming Courses
Sailor Resources
ASA Log Book
Bite Sized Lessons
Knots Made Easy
Catamaran Challenge
Sailing Vacations
Sailing Cruises
Charter Resources
International Proficiency Certificate
Find A Charter
All Articles
Sailing Tips
Sailing Terms
Destinations
Environmental
Initiatives
Instructor Resources
Become An Instructor
Become An ASA School
Member / Instructor Login
Affiliate Login

Tall Ships Are a Slow Travel Adventure—Here’s Where to Find Them in the U.S.

A historic experience yes, and lots of fun..

Copy Link copied

Travel with a sense of adventure on tall ships like the Matthew Turner .

Photo by John Skoriak

White sails dot San Francisco Bay all year—thanks to its moderate climate. For those lucky enough to own or have access to a boat, it’s one of the most inviting and scenic urban playgrounds in the nation. I’m not a sailor and don’t know any sailors, but this past spring I went sailing one Saturday afternoon on the Matthew Turner , a tall ship that sails out of Sausalito. In addition to a history lesson, I gained a fresh perspective of the bay, after decades of living and working near it. The primary mission of the Matthew Turner is teaching sailing to young people, but it also offers passage to the general public.

Before I stepped on the ship’s deck, the closest I’d gotten to this form of slow travel was in books about seafaring explorations centuries earlier. And aside from short ferry rides to Angel and Alcatraz islands, my only previous sailing on SF Bay did not augur well. That was on the Oceanic Society’s 60-foot motorboat heading 25 nautical miles west to the Farallon Islands; half of the eight hours aboard were choppy. Although I didn’t get seasick, I also didn’t eat the apple I’d brought along. And several passengers looked as though death could not come soon enough.

In contrast, sailing via Call of the Sea on the larger MT was smooth—and among assorted small sailboats and gigantic cargo ships, it’s the classiest boat on the bay. With wind power, traveling at about five knots per hour, it’s genuine slow travel. That speed lets you take in the scenery, which includes dolphins, seals, birds, and wind surfers among the other vessels. It also lets you appreciate the vast size of the bay: Rocky Alcatraz, green Angel Island, and the Golden Gate Bridge were backdrops, not closeups. The winds determine the route. And the fresh air vanquished the theme from Gilligan’s Island (“a three-hour tour”) that had been stuck in my head for days.

Built in the 21st century, over seven years, the Matthew Turner is named for the designer and builder of the brigantine Galilee, which had an advanced design for its time, in the late 19th century. (The Galilee long held the passage record of 19 days from San Francisco to Tahiti.) The fir and oak 132-foot MT brigantine has 11 sails (including several that are square); the main mast rises 100 feet. Its few modern features include an electric hybrid motor used for leaving the harbor. Otherwise, it’s strictly wind powered. That means no smell and no noise—aside from the crew leader calling out instructions about modifying sails—on an eco-friendly trip.

The brigantine sails on select Fridays, Saturdays, and Sundays throughout the year, ranging from 90 minutes to several hours . When I booked in May, I skipped the Mother’s Day special, figuring it would be crowded (it sold out) and got lucky: The amiable, enthusiastic young crew outnumbered the passengers. I chatted with nearly everyone aboard, including Alan Olson, the force behind the original project to build the ship. Highlights included watching the crew, which included a few volunteers and several women, set the sails. At the end of the too-short, two-hour trip, they scampered up the rigging to the top of the masts to roll up and tie the sails closed. So many ropes and sails: It’s not easy to travel this old-school way.

Among the passengers was a couple who had sailed on the ship before. I didn’t need to ask why.

Photo on the left displays a tall ship; Photo on the right displays sailing ropes

Oftentimes, tall ships offer sailing classes.

Photos by Pat Tompkins

How to find your own tall ship adventure

Opportunities to participate in a day sail in the USA are more widely available than you might think. That’s partly because “tall ship” includes topsail and two- and three-masted schooners, barques, and other sailboats smaller and less grand than the Matthew Turner . Many tall ships with trips open to the public also operate as hands-on “classrooms” with programs to teach young people how to sail. For example, the Los Angeles Maritime Institute has tall ships for families or groups to charter; these private charters help support the educational programs.

You’ll find more possibilities through Tall Ships America, an organization based in Newport, Rhode Island, that promotes learning to sail and learning from sailing.

Where to sail on a tall ship in the United States

Book now: Seattle’s Tall Ship ; Tall Ship Lady Washington

See the city from a tall ship on the gaff-rigged schooner Bay Lady , an 85-footer. A two-hour sail from Seattle’s Tall Ship starts at $45 for adults; $35 for kids 2–12; there are several sailings daily on Puget Sound from late April through the end of October.

Another nearby option: the Lady Washington brig, the official tall ship of the state of Washington, has day sails of two hours or more during July from Anacortes, Port Ludlow, Everett, and other cities. It’s a replica of the original Lady Washington , the first U.S. ship to sail the West Coast. For a two-hour sail: $70 for adults, $50 kids 4–12; four-hour voyages are also available.

Book now: Pride of Baltimore II

Besides public two-hour sails, the Pride of Baltimore II , a topsail schooner, provides several guest crew opportunities for hands-on experience during the summer. While it visits New York in July, evening two-hour trips are available from Greenpoint on Long Island on the 19th and 20th (adults $55, $35 kids).

Book now: Tall Ship Adventure

Enjoy a tall ship trip on the Californian through the Maritime Museum of San Diego. In addition to four-hour sails on Sundays (through October) at $119 for adults, $69 for children 3–12, this summer, for the first time since 2020, the Maritime Museum offers two chances for families to spend the night aboard the 1863 Star of India. (The boat stays docked but staff will teach the night’s “crew” about life for sailors long ago.) Overnights are Friday July 26 and August 9, 2 p.m. to 9 a.m., with two meals, $125 per person.

Book now: Tall Ship Windy

Aboard the 148-foot schooner Windy , offerings include a daily Chicago Skyline tour from Lake Michigan (75 minutes; $49 adults, $39 kids) and an educational 90-minutes hands-on sail (Saturday–Monday, $35 adults, $25 kids). Summer features two-hour blues concert trips on Monday nights, $59 adults, $49 kids.

Gloucester, Massachusetts

Book now: Schooner Adventure

During a 2.5-hour jaunt from the nation’s oldest fishing port, Gloucester Harbor, passengers can participate—helping raise the sails—or not, as they wish. You’ll be on the restored 1926 Adventure , a dory-fishing schooner and a National Historic Landmark. Those age 18 and under can enjoy the experience for free; tickets for adults are a modest $52. The Adventure offers public trips June through September on Sunday afternoons and Friday evenings.

A projection show called Hogwarts Always at The Wizarding World of Harry Potter, displaying fireworks igniting behind the Hogwarts castle

Bodies of two children recovered after sailboat capsizes, search continues for missing man

by Emily Matesic, FOX 11 News

{ }Missing man and kids in Door Co. Last seen Saturday, July 13, 2024 (Brown Co. Emergency Management)

UPDATE: The children's names have been released .

FISH CREEK (WLUK) -- The bodies of two young children were found after their sailboat was found capsized in the waters of Door County.

"My heart is in my stomach. As a boater, we've been boating 50 years and to see a boat pull in and not know where the captain or two small children are, that's a boater's worst nightmare," said Kathy Hinkfuss of Green Bay, a recreational boater.

A search began over the weekend for the two children, ages 3 and 5, and their father, 32-year-old Bill Salnik of Little Suamico, after they went sailing Saturday.

Officials say the three left Oconto Harbor after 10 a.m.

Around noon Sunday, the Oconto County Sheriff's Office received a report of an overdue boat and began a search with the U.S. Coast Guard and the Wisconsin DNR.

"The Oconto County Sheriff's Office began a search along with the USCG and the WI DNR. The search expanded last night into the jurisdictional waters of Door County. Emergency personnel from the DCSO, DC emergency services and local fire departments joined the search," said Chief Deputy Patrick McCarty with the Door County Sheriff's Office.

The family's intended route was to go from Green Island in the bay to a marina just south of Oconto but they never made it to their destination.

Salnik's truck and trailer was still at the boat ramp and his phone calls went straight to voicemail.

At 6:22 a.m. Monday, the capsized sailboat was found just south of Chambers Island, without Salnik and his children. The vessel was was towed to Fish Creek.

After 11 a.m. Monday, searchers found the bodies of the two young children about a mile south of where the sailboat was found. "The bodies of two young children were recovered in the water about one mile south of where the boat was located. Their names are not being released at this time pending positive identification and notification of next of kin," added McCarty.

The Door County Sheriff's Office says they will continue their land and sea search efforts to find Salnik.

Due to warmer water and air temperatures, officials say it is still possible to find Salnik alive.

Officials are asking those out on the water to keep an eye out for anything that may be related to the search for Salnik.

These 3 lesser-known cruise lines offer amazing voyages on sail-powered ships

There is nothing quite as magical — or romantic — as a cruise on a sailing ship.

To stand on the deck of a vessel topped with dozens of billowing sails, propelled through the waves by the power of the wind alone, is to go back in time to an earlier age of travel, when crossing the world's oceans was as adventurous as it was challenging.

It's an experience that's all about the feeling of the wind in your hair, the lean of the vessel (known as the heel) as it's pushed by the wind and the sway from the waves (which is actually smoother than what you get on a motor ship).

For more cruise guides, news and tips, sign up for TPG's cruise newsletter .

In contrast to what you'll find on so many motor-powered ships, cruising on a masted ship is about the simple thrill of traveling across the sea and not about all the many attractions you'll find on board.

Only a handful of small cruise brands — so small that you might never have heard of them — offer trips on sailing ships. Here, we look at the three biggest players in this niche subset of the cruise industry.

Sea Cloud Cruises

If it's an authentic, old-style sailing experience you want, then Sea Cloud Cruises is the line for you. The Germany-based company operates three large sailing ships where the sails are unfurled by hand, just as they were on sailing ships centuries ago.

On the biggest of these three vessels, the 136-passenger Sea Cloud Spirit , 18 deckhands scurry high into the rigging on sea days to manually untie and prepare the sails, an amazing sight. Unveiled in 2021 , it's a full-rigged, three-masted sailing ship of the sort that hasn't been common on the world's oceans for more than a century.

Related: Why Sea Cloud Spirit is a sailing vessel you'll want to try

Sea Cloud Cruises' two other vessels — Sea Cloud 2 and Sea Cloud — are smaller but offer a similar show as the sails are set by hand the old-fashioned way. The former is a 23-year-old, three-masted barque propelled by 23 sails (five fewer than Sea Cloud Spirit); the latter is a 93-year-old, four-masted barque with 30 sails and a storied past.

Now configured to carry 64 paying passengers, Sea Cloud was originally the private yacht of Postum Cereals heiress Marjorie Merriweather Post and her husband, the famed financier E. F. Hutton. At the time, the vessel was the largest private yacht in the world. It later served the U.S. Navy as a weather ship during World War II, after which it became the presidential yacht for the Dominican Republic. It only began sailing as a cruise vessel in the 1980s.

If you have money to spare, you can still book Post's opulent private quarters on Sea Cloud, now its owner's suite. It'll set you back around $5,000 per day per couple. Her husband's slightly smaller quarters are also available to book at a similar rate.

Post, the wealthiest woman in the U.S. during her lifetime, notably also built Mar-a-Lago, the massive estate in Florida that is now the official residence of Donald Trump.

Sea Cloud Cruises is the most all-inclusive and upscale of the three brands listed in this story, with pricing to match. Expect to pay nearly $1,000 per person per day or more for many sailings.

Sea Cloud Cruises' three vessels offer a diverse array of sailings in the Mediterranean, Northern Europe, the Canary Islands and Morocco, the Caribbean or along the west coast of Central America.

Related: Cruising Costa Rica, Panama with Sea Cloud Cruises

Windstar Cruises

Founded in the 1980s, Windstar Cruises got its start as a sailing ship line. While it now operates traditional motor-powered ships, too, voyages on sailing ships are still a big part of its business.

Three of the Seattle-based brand's six vessels — Wind Spirit, Wind Star and Wind Surf — are sailing vessels, and they all offer a similar yacht-like, small-ship experience.

Two of the three vessels (Wind Spirit and Wind Star) are particularly intimate, measuring 5,407 tons and carrying just 148 passengers with every berth full.

Related: The 2 types of Windstar ships, explained

The line's third sailing vessel, Wind Surf, is nearly three times the size at 14,745 tons. It's one of the biggest sailing ships in the world (only a sister vessel that sails for Club Med is bigger). Wind Surf carries 342 people, an enormous number for a sailing ship.

Unlike on the vessels operated by Sea Cloud, the sails on Windstar's sailing ships aren't unfurled by hand in the old-fashioned way but by the push of a button from the bridge. It's a fully automated system that is much more modern, if less dramatic.

Still, the experience of slicing through the waves by the power of the wind alone on Windstar ships is as glorious and romantic as it is on the Sea Cloud ships.

Windstar Cruises is less all-inclusive and pricey than Sea Cloud but still offers a relatively upscale experience. Its dining program is done in partnership with the food-focused James Beard Foundation, which also brings James Beard Award-winning chefs to the ships regularly for food-themed itineraries.

For an extra $89 per person per day, passengers can also make the experience more all-inclusive with included Wi-Fi, unlimited beer, wine and cocktails, and gratuities (three things that aren't included in regular fares).

The line's three vessels typically spend nearly all of their time sailing in the Mediterranean, the Caribbean or along the west coast of Central America.

Related: Read more about Windstar's itineraries

Star Clippers

Like Sea Cloud and Windstar, Star Clippers operates three sailing vessels that are among the biggest and most elegant sailing vessels in the world.

The belle of the ball at the line is Royal Clipper, a stunning five-masted ship that is billed as the largest square-rigged ship in the world. Its enormous array of 42 sails has a sail area of 56,000 square feet — significantly more than the sails atop any of the Sea Cloud or Windstar vessels. (Only Sea Cloud Spirit comes relatively close with a sail area of 44,100 square feet spread across 28 sails.)

Built to resemble Preussen, a legendary tall ship of the 19th century, the 24-year-old Royal Clipper shares the spotlight at Star Clippers with two smaller sister vessels, Star Flyer and Star Clipper.

Carrying 166 passengers apiece, the smaller vessels were designed to resemble the speedy clipper ships of the 19th century, which were known for their narrow profile and large sail area. Each vessel has a sail area of 36,000 square feet spread across 16 sails, a large amount for the size.

When it comes to the setting of sails, Star Clippers vessels offer a level of old-style authenticity that is in between the ships of Sea Cloud and Windstar. Like on Sea Cloud vessels, the sails are pulled into position by a team of deckhands using hand power and winches to tighten the "sheets," or ropes.

Unlike on Sea Cloud vessels, the deck hands don't climb high into the rigging to untie and prepare the sails for winching. That part is done automatically at the push of a button from the bridge, as it is on Windstar vessels.

In one key difference, though, Star Clippers lets passengers harness up and climb into the crow's nest of its vessels — a thrilling experience. Just be prepared for your knees to go a bit wobbly as you get to the top; it's way up there.

Star Clippers sailings are the most affordable option among the three sailing brands, in part because the onboard experience is less all-inclusive and upscale.

The three Star Clippers vessels mostly operate sailings in the Mediterranean, the Canary Islands, the Caribbean and along the west coast of Central America.

Bottom line

It's still possible to get a taste of what traveling the world's oceans was like in the days before motor power. Three small cruise companies — Sea Cloud Cruises, Windstar Cruises and Star Clippers — offer voyages on large sailing ships that are as majestic as anything that has sailed the seas in centuries past.

Planning a cruise? Start with these stories:

The 5 most desirable cabin locations on any cruise ship
A beginners guide to picking a cruise line
The 8 worst cabin locations on any cruise ship
The ultimate guide to what to pack for a cruise
A quick guide to the most popular cruise lines
21 tips and tricks that will make your cruise go smoothly
Top ways cruisers waste money
The ultimate guide to choosing a cruise ship cabin

Editorial disclaimer: Opinions expressed here are the author’s alone, not those of any bank, credit card issuer, airline or hotel chain, and have not been reviewed, approved or otherwise endorsed by any of these entities.

CLASSIFIEDS
NEWSLETTERS
SUBMIT NEWS

Rolex TP52 World Championship at Newport, RI - Day 3

Rolex TP52 World Championship Day 3 - photo © Nico Martinez

Grand Rapids/Muskegon
Saginaw/Bay City
All Michigan

Chicago to Mackinac sailing race record smashed by more than an hour

Updated: Jul. 15, 2024, 7:31 a.m.
| Published: Jul. 15, 2024, 7:20 a.m.

The Maverick broke a 22-year record in the 115th Chicago Yacht Club Race To Mackinac Presented By Wintrust. Chicago Yacht Club Race To Mackinac

Tanda Gmiter | [email protected]

MACKINAC ISLAND, MI - Before the first boats ever left Navy Pier this weekend, Chicago Yacht Club Race to Mackinac organizers knew the weather forecast would make this 115th competition one of the faster courses in the race’s history - if the sailing crews could avoid the storms forecast to sweep across Lake Michigan.

And while the storms did send at least three damaged boats limping out of the race and caused a man overboard situation, southerly wind conditions were a boon to the frontrunners, creating a downwind drag race and leading to a record-breaking win that smashed the old Race to Mackinac record by more than an hour.

The Maverick’s crew beat Roy P. Disney’s 22-year-old record with a time of 22 hours, 24 minutes, 23 seconds. This bested the Disney heir’s record set in 2002 with Pyewacket by an hour, six minutes and 11 seconds.

The Maverick team was led by Sanford Burris and William and Ward Kinney. The boat also claimed the race’s Royono Trophy for the first racing monohull to finish the 115th edition.

“I will tell you from my perspective, I wish the record had lasted longer, but these things are inevitable,” said Disney, a well-known figure in the sailing world who is the grand-nephew of Walt Disney. “Given how long it took to break that record shows how difficult a course it is, and what a classic sailboat race it is! Many congratulations to the owner, the crew and the boat, Maverick.”

The Katana and the Natalie near the finish line of the 115th Chicago Yacht Club Race To Mackinac Presented By Wintrust. Chicago Yacht Club Race To Mackinac

Nearly 250 boats joined the 333-mile race from Chicago’s Navy Pier to the finish line near Mackinac Island. Known as America’s Offshore Challenge, it’s the world’s longest annual freshwater sailing race. The race is divided into the Cruising Division, which left Chicago on Friday, and the sleeker Racing Division, which began racing on Saturday.

What was the secret to this weekend’s fast times?

“Most important is a southerly wind direction and strength, combined with advancements in boats and sails,” said Winn Soldani, chair for the 115th Chicago Yacht Club Race to Mackinac presented by Wintrust. “Plus you add in last night’s storms that brought increased breeze and it’s literally the perfect setup for a record-breaking year.”

Some of the boats are still finishing the course today. You can see them there on the race tracker.

Maverick’s Sanford Burris is from Kirtland, Ohio. “He sails with his sons and many longtime friends on the carbon fiber Andrews 80 they have spent the past three years upgrading. Joining the 20 crew onboard was Evolution Sails founder Rodney Keenan,” race staff said.

“The team celebrated briefly as the Maverick team crossed the Race to Mackinac finish line between Mackinac Island and the Round Island lighthouse … and then kept on sailing.”

The Maverick is one of a couple dozen sailboats competing in this year’s “Super Mac” race - which means it keeps going instead of stopping at Mackinac Island for the big afterparty. It races south down Lake Huron to reach Port Huron - a race of 495 nautical miles. The Bayview Mackinac Race - which is next week - starts near the Blue Water Bridge and competing sailboats will race north to Mackinac Island. Those boats running the “Super Mac” can also do the Bayview and it’s like running three races in a week’s span.

The Racing Division of the 115th Chicago Yacht Club to Mackinac race got underway Saturday. Photo provided by Barry Butler, Chicago Yacht Club Race to Mackinac presented by Wintrust. Barry Butler, Chicago Yacht Club Race to Mackinac presented by Wintrust.

If you purchase a product or register for an account through a link on our site, we may receive compensation. By using this site, you consent to our User Agreement and agree that your clicks, interactions, and personal information may be collected, recorded, and/or stored by us and social media and other third-party partners in accordance with our Privacy Policy.

IMAGES

Sailboat Keel Types: Illustrated Guide (Bilge, Fin, Full)
The Ultimate Guide to Sail Types and Rigs (with Pictures)
Sailboat Rigging and Some Nomenclature
How To Sail A Boat
Different Sail Types Explained (9 Types of Sails)
Ship

VIDEO

Three quick sailboat repairs #sailinglife #liveaboard #boatlife
Canoe Sail Kit from SailboatsToGo.com Flies Across Lake
Interveiw with George of Three Sails Studio
Three Day Sailing Trip, Part 1
Sail Making (Pentex Tri Radial Genoa)
We Had A Sailing Mishap... But Ended Up With A Better Sail! #sailboat #shortvideo #sail

COMMENTS

The Ultimate Guide to Sail Types and Rigs (with Pictures)
Boats with one mast can have either one sail, two sails, or three or more sails. The 3 most common one-masted rigs are: Cat - one mast, one sail; Sloop - one mast, two sails; Cutter - one mast, three or more sails; 1. Gaff Cat Cat boat with single gaff-rigged sail 2. Gaff Sloop Sloop with gaff rig 3. Cutter
The Different Types Of Sails And When To Use Them
As a general setup, sailboats will use three common sails, including headsail, mainsail, and specialty sail. Due to the varying wind conditions and the model of the sailboat, there are many types of sails including jib, genoa, trysail, storm jib, code zero, gennaker, and spinnaker. While that sounds like too many models of sails, you can easily ...
The Different Types of Sails On A Sailboat: An Easy Guide
A sloop-rigged sailboat typically features a mainsail, a headsail, and an additional light-wind sail, such as a spinnaker or Gennaker. The mainsail is rigged aft of the mast, while the headsail is attached to the forestay. The two most commonly used headsails are the Genoa and Jib. The sails are vital parts of a sailboat since you obviously ...
Parts Of a Sail Explained (Illustrated Beginners Guide)
A sail, which is a large piece of fabric that is attached to a long pole called the mast, uses the wind to pull a sailboat across the water. It has various parts, such as the head, tack, clew, luff, leech, foot, mainsail, jib, and batten. These components determine the shape and efficiency of the sail.
Sail Types: A Comprehensive Guide to 8 Types of Sails
3. Genoa. The genoa is a large sail that attaches to the front of the forestay. (In this instance, it's similar to a headsail.) However, the genoa is larger than the headsail and overlaps the mainsail partially or completely to help the boat go faster. Genoa sails are useful when sailing through light or medium wind.
Most Popular Types of Sails on a Sailboat
The mainsail, headsail (or jib), genoa, spinnaker, and gennaker are the most popular types of sails on sailboats. There are also a number of different configurations when considering the type of sail and mast in use including a sloop, fractional rig sloop, cutter, ketch, schooner, yawl, and cat. Simply put, different sailboat sails serve ...
Types Of Sails On Sailboats: A Comprehensive Guide
Sail shape is an important factor in determining the performance of a sailboat. Different sail shapes are designed for different wind conditions, and the choice of sail shape can greatly affect a boat's speed and maneuverability. Here are three common sail shapes: Bermuda Rig. The Bermuda rig is the most common sail shape on modern sailboats.
The different types of sails and their uses
Mainsails are essential for providing the boat with forward propulsion and play a significant role in steering and balancing the vessel. There are two primary types of mainsails: full-batten and partial-batten. Full-batten mainsails have horizontal battens that run the entire width of the sail, providing additional support and shape.
Types of Sails: A Comprehensive Guide
Spinnaker sails are a type of downwind sail that can be used to increase boat speed when sailing in light winds. They are typically used in wind conditions below 10 knots, which are considered light air sails. Spinnakers come in two types: symmetrical and asymmetrical. Author: Ken Heaton CC BY-SA-4..
Sail Types: A Comprehensive Guide to Different Types of Sails
The three main types of sails used in sailing are mainsails, headsails, and spinnakers. Mainsails are generally located near the centerline of the boat and provide the primary driving force for propulsion. ... The mainsail is the primary sail on a sailboat, providing the main source of propulsion. Its design allows it to capture wind from ...
Guide to Understanding Sail Rig Types (with Pictures)
Gaff ketch - two-masted (mizzen), two mainsails, staysails, fore-and-aft rigged. Full-rigged ship or tall ship - three or more masts, mainsail on each mast, staysails, square-rigged. The first word is the shape and rigging of the mainsail. So this is the way the sail is attached to the mast.
Type Of Sails: A Complete Guide to Sails
Sloop. A sloop is by far the most popular configuration. It features a single mast, double sail (the mainsail and the headsail), and mast configuration. The headsail is located from the forestay on the mast to the top of it. The type of headsail used can also vary from a genoa, a spinnaker, or a gennaker sail.
Names of Sails on a Sailboat
Leech: Back edge of the sail. Tack: The lower front corner of the sail. Clew: The bottom back corner of the sail. Foot: Bottom of the sail. There are two sail shapes, the fore-and-aft rigged sails, and square-rigged sails. Nowadays, fore-and-aft sails are more popular, have better performance and maneuverability.
Different Types of Sails: A Comprehensive Guide
Short answer different types of sails: There are several different types of sails used in sailing, including mainsails, headsails (jibs and genoas), spinnakers, gennakers, and storm sails. Each type is designed for specific wind conditions and sailing techniques, contributing to the overall performance and maneuverability of a sailboat. Understanding the Basics: Exploring Different Types of
Beginner's Guide to Types of Sails
The shape of the sail plays a crucial role in how it works. Sails are designed to be curved, much like an airplane wing. This curvature creates differences in air pressure: the wind flowing over the curved side of the sail travels faster and creates lower pressure, while the wind on the flat side (facing the wind or windward) remains relatively slower with higher pressure.
Types of Sails for Sailboats: A Comprehensive Guide
Sailboats typically use four primary types of sails: mainsails, genoas/jibs, spinnakers, and staysails. Mainsails are the largest and provide forward propulsion. Genoas/jibs enable efficient sailing upwind. Spinnakers are used for downwind sailing and maximizing speed. Stay-sails provide stability in heavy wind conditions.
Types of Sails on a Boat
This boat has three masts and 25 sails in total. Before engine power, sailors relied entirely on the wind to move their ships. Faster ships meant that produce had less time to spoil. The faster your ship was, the more competitive it was. Arriving with the first batch of sugar or fine wine would gather more interest and excitement at the dock ...
Sailing Terms: Sailboat Types, Rigs, Uses, and Definitions
Sailboat Types There are many different types of boats for sailing, differentiated by three distinctive characteristics: Hull Type (monohull, catamaran or trimaran); Keel Type (fin keel, wing keel, bilge keel, daggerboard, or centerboard); Mast Configuration and Sails (sloop, fractional rig sloop, ketch, schooner, yawl, cutter, cat); Let's explore those different types in a little more detail.
Types of Sailboats: A Complete Guide
The rig of a sailboat refers to it's mast and sail configuration. Here are the most common types of sailboat rigs and what they're used for. ... Schooners have a minimum of two masts, but some have three or more. The aftermost large sail is the mainsail, and the nearly identical forward sail is called the foresail. Schooners can have one or ...
How Sails Work: Understanding the Basics
The shape of the sail is ideal when the strands on both sides are streaming back at the same level, which indicates that wind is moving evenly along both sides of the sail. READ MORE: Parts of a Sailboat. Points of sail. A boat cannot sail directly into the wind- instead, it sails at an angle to the true breeze.
Different Types Of Sailboats Explained: A Comprehensive Guide
Contents show. Several factors determine the types of sailboats, including the hull type, keel type, mast configuration, and sails and rigging. The hull is the boat's body and can be either a monohull, catamaran, or trimaran. The keel is the underwater part of the hull that provides stability and can be either a fin keel, wing keel, bilge ...
Sailboat Types: Full-Guide 2024
For example, a sailboat with just one big sail on a forward-mounted mast is called a catboat. A boat with dozens of different sails on three masts is called a three-mast schooner. Small Sailboats. ... This type of sailing boat has two hulls and offers sailors speed, space, and comfort. A cruising catamaran is usually between 40 and 60 feet long ...
Students build their own boat and plan to sail on Detroit River
A hands-on workshop. Brother Ari and Eli Boyce, 14 and 13, of Detroit, have sailed with the Detroit Community Sailing Center's Challenge the Wind youth program for three years and welcomed the ...
Secrets of Successful Cruising
Join Julie Capelli, of Pelagic Cruising Services, as she breaks down tips for mastering the secrets of successful cruising. Learn essential skills from sailing basics to self-sufficiency, and gain insights on boat selection and preparation. And don't miss the opportunity to hear directly from the author, transformed full-time sailor from landlubber, at the Annapolis Sailboat Show October 11, 2024!
What It's Like Sailing on a Tall Ship in the U.S.
How to find your own tall ship adventure. Opportunities to participate in a day sail in the USA are more widely available than you might think. That's partly because "tall ship" includes topsail and two- and three-masted schooners, barques, and other sailboats smaller and less grand than the Matthew Turner.Many tall ships with trips open to the public also operate as hands-on ...
Bodies of two children recovered after sailboat capsizes, search
A search began over the weekend for the two children, ages 3 and 5, and their father, 32-year-old Bill Salnik of Little Suamico, after they went sailing Saturday. Officials say the three left ...
These 3 lesser-known cruise lines offer amazing voyages on sail ...
The former is a 23-year-old, three-masted barque propelled by 23 sails (five fewer than Sea Cloud Spirit); the latter is a 93-year-old, four-masted barque with 30 sails and a storied past.
Rolex TP52 World Championship at Newport, RI
Posted on 11 Jul Optimising sail trim: Upwind vs downwind Perhaps the single most important factor in boat performance Sail trim is perhaps the single most important factor in boat performance. Whether you're a weekend dinghy sailor or you sail on a 100-ft maxi, adjusting sail shape to maximise the wind that you have at your disposal is the ...
Review: Outremer 52 Top 10 Best Boats 2025 Nominee
Our sail took place in lumpy seas and shifting winds off Miami Beach. The big wind had come through the day before, but the sketchy breeze wasn't going to dampen our fun. In 10 knots of true breeze, we made good 6.1 knots of boatspeed. In the puffs you could immediately feel the boat accelerate as she jumped up to 9.2 knots in 14 knots of wind.
Chicago to Mackinac sailing race record smashed by more than an ...
"He sails with his sons and many longtime friends on the carbon fiber Andrews 80 they have spent the past three years upgrading. Joining the 20 crew onboard was Evolution Sails founder Rodney ...

The Different Types Of Sails And When To Use Them – Complete Guide

Different Types of Sails & When To Use Them

2. Headsail

2.2 Genoa

3. Specialty Sail

3.1 Spinnakers

3.2 Storm Jibs

3.3 Code Zeros

3.4 Trysail

3.5 Gennakers

How Many Sails On A Sailboat ?

Why Are There Two Sails On A Sailboat?

Final Thoughts

Recent Posts

The Most Popular Types Of Sails On A Sailboat

The different types of sails on a sailboat

Light-wind sails

The standard sails

Mizzen Sail

Storm Sails

Storm Mainsail

Explaining the terms for the parts of a sail

Traditional and less commonly seen sails

Square sails

Jib-headed topsail

Sprit sails

Lateen sails

Popular sail and mast configurations

Bermuda Sloop Rig

Final words

FAQ: The Different Types of Sails On A Sailboat

What is the difference between a loose-footed and attached-footed mainsail?

What is a high-cut clew on a sail?

What is luff foam on a sail?

What are the most common sails?

What are the different types of sails?

What is a spinnaker sail?

What is a Jib sail?

Is Genoa sail the same as a jib?

What is a Genoa sail?

How many types of sail plans are there?

What is a Mainsail?

What is a Gennaker?

What is a Storm Jib?

What factors determine the type of sail to be used?

How do sails affect the performance of a sailboat?

Leave a Reply Cancel reply

Sail Types: A Comprehensive Guide to 8 Types of Sails

8 Types of Sails for Sailboats

1. Mainsails

2. Headsail

3. Genoa

4. Spinnaker

5. Gennaker

6. Light Air Sails

7. Storm Jib

Join Our Newsletter!

Most Popular Types of Sails on a Sailboat

Types of Sails

Headsail/Jib

Popular Sail and Mast Configurations

Fractional Rig Sloop

Get the very best sailing stuff straight to your inbox

Quick Links

The different types of sails and their uses

The Different Types of Sails and Their Uses

Table of Contents

Downwind Sails

Storm Sails

Types of Sails: A Comprehensive Guide

Different Types of Sails on a Sailboat: Why Use Different Sails at All?

Sail Plans: Different Combinations for Different Boats

Understanding Sail Anatomy

The Head: The Top of the Sail

The Tack: The Lower Front Corner of the Sail

The Foot: The Bottom of the Sail

The Luff: The Forward Edge of the Sail

The Leech: The Back Edge of Your Sail

The Clew: The Bottom Back Corner of Your Sail

Primary Sail Types