corsair 36 catamaran

• AROUND THE SAILING WORLD
• BOAT OF THE YEAR
• Email Newsletters
• Best Marine Electronics & Technology
• America’s Cup
• St. Petersburg
• Caribbean Championship
• Boating Safety

Corsair 36, Fast Cruising Tri

• By John Burnham
• Updated: June 7, 2005

What I thought was the weirdest thing about the boat at first turned out to be one of its outstanding features. The Corsair 36 has a stern deck at the back of the cockpit with two large bench seats made of mesh and stainless steel tubes, and they looked bizarre. But after a day or two of cruising with my wife and three daughters, I looked at those seats with complete appreciation. They were the most coveted, comfortable places from which our crew would sunbathe, snooze, and read. If I was lucky, sometimes I even got to sit in one to steer.

I’d been looking forward to cruising on Corsair’s new flagship and comparing it to our experience on the 31 a few years earlier ( “It’s Not All About Speed,” March ’01 ). Like the 31, the 36 is built with a vacuum-bagged foam/glass sandwich laminate, plus carbon and Kevlar reinforcing. The beams are made entirely with carbon, and the overall weight is a little over 2,000 pounds more than the 31. With 817 square feet of upwind sail area, the tri was fast-roughly as fast as the 31, but without the same twitch in the gut when it accelerated. Under main alone we broad-reached across a windy Vineyard Sound doing a relaxed 12 knots. Later, on a beam reach in about 12 knots on Narragansett Bay, with my 12-year-old daughter steering (one hand on the tiller extension, one hand holding a book), our speed jumped from 11 knots to 15.3 as I trimmed in the main and the sprit-mounted genoa (known as a screacher). And when I crewed in a local race with Multihull Source dealer Bob Gleason, we saw 17 knots on a tight reach. I’m told that reaching speeds in the low 20s are common, but what impressed me most was the light-air trip we made from Martha’s Vineyard, to Jamestown, R.I., in seven hours-40 miles upwind. To me that’s the big benefit of a boat like the 36; you can sail it quickly and quietly, eating up the miles while others are going no faster under iron genoa.

Because of its larger accommodations, compared to the 31, the 36 got the thumbs-up from my daughters. But it’s still a trimaran with a relatively skinny main hull; that’s the price you pay for speed. The narrow waterline reduces storage, but the hull flares outboard above the waterline, which provides room for an enclosed head on one side of the daggerboard trunk, as well as the dinette, which converts to a small double berth. There’s also a small galley area to starboard with a sink and two-burner alcohol stove.

On our boat, the fridge had been removed and an Igloo cooler was used in place of the bottom companionway step; but the standard configuration has a 12-volt fridge to port, just forward of the dinette area. An option is available for a propane-fired stove and propane on-demand hot water. There were five of us aboard, with two girls in the forward cabin, one in the dinette double, and the adults in the aft double, which is reached by lifting part or all of the stern deck at the back of the cockpit. We loved sleeping in that wide aft berth, although getting in and out required agility, and changing clothes in there was like dressing inside a tent. We decided if there were a follow-up cruise, we’d claim the forward cabin and move the girls aft.

Despite the constraints of the interior, the on-deck living spaces are expansive. With amas and trampolines to port and starboard, a small foredeck, plus the stern seats, any of the five of us could escape the others when we felt like it. We could easily carry our tenders-single and double kayaks lashed between the forward and aft beam on one side-and the large-volume outer hulls had plenty of room for storing anchors, paddles, even garbage. On the foredeck and forward beam, we found plenty of room to take solar showers and/or have some fun by dashing outboard and swinging off the spinnaker halyard. Speaking of solar devices, a flexible solar panel lived on the cabintop or port netting and provided an all-day trickle charge to our batteries.

The 36 we sailed was one of the first built, and while we were racing in hard reaching conditions, we heard a crack at theinboard end of the forward beam. Installed under the beam’sinboard end was a fiberglass block that gives a tight fit for the beam after it’s unfolded and bolted to the main hull. “The block we made,” says Paul Koch, Corsair’s president and design team member, “wasn’t up to the job. We’ve replaced it on all boats with a stronger aluminum casting.” Hull No. 8 is under construction at press time.

Overall, I liked the boat’s sailhandling systems-a full-length traveler across the stern deck and pairs of winches for main, jib, and screacher or spinnaker. While racing, I went forward to help with the asymmetric spinnaker and found that it was too big for me to take down to windward unless the skipper was willing to bear off. (For some reason he wanted to keep sailing toward the mark, so we dropped it to leeward instead.) But while cruising, the combination of the roller-furling headsails (jib and screacher) and a mainsail equipped with lazy jacks and jiffy reefing made sailhandling easy.

It was tough to balance on the boom to remove the full-length batten in the square-top mainsail, and I figured that was another small price to pay for performance. I learned later from sailmaker Dave Calvert that a quick-pin on a new Tides Marine batten-car design now releases the head so the batten can lie flat along the boom. Under power, with a 15-hp, long-shaft, four-stroke Honda, the 36 moved well and steered easily thanks to a small bar that is dropped into place to link the top of the engine and the outboard, kick-up rudder. An electric starter and power tilt made getting underway simple.

Compared to other Corsairs, which go on and off their trailers quickly, the 36 is a much more substantial boat. It’s considered a “transportable,” not a “trailerable” boat, in the sense that it’s not the type of boat you’ll launch for a quick afternoon sail. Except when traveling to new sailing areas, it will probably live on the end of a dock or a mooring-or in about five minutes it can also be folded up to fit in a slip. Manufacturer estimates for stepping the mast and launching are about two hours.

If your kids like to read and swim and you like to sail from harbor to harbor-whether at 17 knots in a breeze or 6 knots in light airs, go for a test sail . With a few agile, fit crewmembers to manage the spinnaker, you can race it hard as well. Whatever you do, don’t let the funky bench seats put you off.

Corsair 36 LOA 36’0″ LWL 35’0″ Beam (overall) 25’7″ Beam (folded) 9’10” DSPL 5,500 lbs. Draft (hull only) 1’8″ Draft (daggerboard down) 6’0″ Mast length 47’6″ Sail area 817 sq. ft. (1,084 w/screacher) Base price $208,000 www.corsairmarine.com

• More: Corsair , Sailboats , Trimaran
• More Sailboats

Nautor Swan Has A New Pocket Rocket

Pogo Launches its Latest Coastal Rocket

A Deeper Dive Into the Storm 18

2024 Boat of the Year Best Recreational Racer: Z24

Jobson All-Star Juniors 2024: The Fast Generation

Wingfoiling Gear: A Beginner’s Guide

Caudrelier Wins Round-the-World Solo Sprint

A Tale of Two Macs

• Digital Edition
• Customer Service
• Privacy Policy
• Terms of Use
• Cruising World
• Florida Travel + Life
• Sailing World
• Salt Water Sportsman
• Sport Fishing
• Wakeboarding

Many products featured on this site were editorially chosen. Sailing World may receive financial compensation for products purchased through this site.

Copyright © 2024 Sailing World. A Bonnier LLC Company . All rights reserved. Reproduction in whole or in part without permission is prohibited.

• New Sailboats
• Sailboats 21-30ft
• Sailboats 31-35ft
• Sailboats 36-40ft
• Sailboats Over 40ft
• Sailboats Under 21feet
• used_sailboats
• Apps and Computer Programs
• Communications
• Fishfinders
• Handheld Electronics
• Plotters MFDS Rradar
• Wind, Speed & Depth Instruments
• Anchoring Mooring
• Running Rigging
• Sails Canvas
• Standing Rigging
• Diesel Engines
• Off Grid Energy
• Cleaning Waxing
• DIY Projects
• Repair, Tools & Materials
• Spare Parts
• Tools & Gadgets
• Cabin Comfort
• Ventilation
• Footwear Apparel
• Foul Weather Gear
• Mailport & PS Advisor
• Inside Practical Sailor Blog
• Activate My Web Access
• Reset Password
• Pay My Bill
• Customer Service

• Free Newsletter
• Give a Gift

How to Sell Your Boat

Cal 2-46: A Venerable Lapworth Design Brought Up to Date

Rhumb Lines: Show Highlights from Annapolis

Open Transom Pros and Cons

Leaping Into Lithium

The Importance of Sea State in Weather Planning

Do-it-yourself Electrical System Survey and Inspection

Install a Standalone Sounder Without Drilling

Rethinking MOB Prevention

Top-notch Wind Indicators

The Everlasting Multihull Trampoline

In Search of the Snag-free Clew

What’s Involved in Setting Up a Lithium Battery System?

Reducing Engine Room Noise

Breaking Point: What Can Go Wrong With Your Yanmar?

Mildew-resistant Caulks for Boats

Can We Trust Plastic Boat Parts?

Repairing Molded Plastics

Mailport: Marine plywood, fuel additives, through bolt options, winch handle holders

The Day Sailor’s First-Aid Kit

Choosing and Securing Seat Cushions

Cockpit Drains on Race Boats

Rhumb Lines: Livin’ the Wharf Rat Life

Resurrecting Slippery Boat Shoes

Shoe Goo’s Gift to Sailors

Tricks and Tips to Forming Do-it-yourself Rigging Terminals

Marine Toilet Maintenance Tips

Learning to Live with Plastic Boat Bits

The Ultimate Guide to Caring for Clear Plastic

• Sailboat Reviews

The new Corsair is a fast cruising platform, light and bright belowdecks, but with a bit less elbow room than you'd find on a 36-foot monohull, and pricy. For many, these are worthy trade-offs.

Twenty years ago, when Corsair Marine first entered the U.S. market with the F-27 trimaran (which PS reviewed in September, 1990), “family” multihulls were not generally thought to have stellar sailing characteristics. They were difficult to tack. They did not sail well to weather. They required large parking places. In ensuing years, Corsair’s 24- to 31-footers have helped change the perception in the marketplace. These boats are fast, sail well, and are easily trailerable since they fold to 8′ 6″. The major shortcoming has been accommodations that are one cut above camping. The introduction of the Corsair 36 has allowed the company to step into the real world of “cruising comfort.”

Company History Corsair Marine was founded in 1983 by John Walton (of the Wal-Mart family), who envisioned production of a fast, easily trailerable trimaran. A compromise would be accommodations limited by the narrow beam of the main hull.

Walton convinced Ian Farrier, a talented multihull designer, to abandon a thriving practice in Australia, move to California, and execute his vision.

In a morning-long session with PS, Farrier, who sees the world only through multihull lenses, elaborated on the many reasons he considers multis preferable to monohulls, not the least of which is that, “Corsair boats are unsinkable. They have watertight compartments, so even if they pitchpole the crew can crawl inside a capsized hull and have air to breathe and protection from the elements. In a monohull, the crew will most likely be adrift in a liferaft.”

Walton and co-owner Paul Koch, also an Aussie, succeeded, despite the complicated, people-intensive construction process necessary to produce foldable boats capable of withstanding loads endured at sea and on the highway. A by-product was pricing that ratcheted the boat to the very high end of the market when measured on a cost-per-foot basis.

Prior to introduction of the Corsair 36 in February, 2003, the company’s line included the 24-, 27-, and 31-foot models. Boats were built primarily in Chula Vista, California, though the first six F-31s, introduced in 1992, were built at Tillotson-Pearson (TPI) in Rhode Island.

In 1994, Koch purchased Walton’s share and consolidated all of the manufacturing operations at the California plant, where boats are now built.

In its first two decades, Corsair has produced 1,260 boats; annual production is typically 72-75 boats, Koch says.

The 36-footer has been well-received; seven have been ordered since its introduction.

Design Though Ian Farrier is credited with the design of the first three models, and influenced the 36-footer, his affiliation with Corsair ended in the mid-’90s. Paul Koch says that a team of in-house engineers and outside consultants are responsible for the design of the 36.

All of the boat’s design elements— hull, deck, and sailplan—bear a strong resemblance to its predecessors, but the extra LOA allows more graceful lines. Her long, low profile is accented by a downward-sloping cabintop and long, narrow, dark windows. Viewed from the bow, the hull presents a fine entry. The amas also have a fine entry, and near-flat sheerline offset by very round shapes and downward curving bottoms.

However, the new model adds enough load-carrying capability to provide creature comforts suitable for extended cruising. She’s only 900 pounds heavier than the F-31, and performs as well under sail.

All of the Corsair boats, when folded, have the appearance of a giant Daddy Longlegs. The 36-footer also features a tilt-up rudder and shallow draft that allows her to anchor in less than two feet of water, or sail onto a beach. In tight quarters, she can be folded when at anchor.

With a folded beam of 9′ 10″ she’s wider than other models, so owners may be required to secure wide-load permits in some states. To assist owners in avoiding the expense of acquiring a trailer ($7,638), and, perhaps, more powerful tow vehicle, the company has organized fleets of truckers that transport the boats for $1.50 mile, including the cost of a driver.

After the introduction of hull #1 (the boat we tested), input from dealers and consumers at two boat shows brought about a few design modifications and refinements.

Deck and Rig Layout The organization of spaces and layout of gear on the C-36 is almost a carbon copy of its predecessors.

The cockpit is as big as those on monohulls of about the same LOA—wide enough to seat a crew of 4-6 comfortably, and narrow enough to allow a shorthanded crew to work large headsails. The regular cockpit seats are well-proportioned, and there’s additional seating set into both sides of the stern pulpit. These mesh-bottomed seats are good places to be while underway, since they’re elevated, clear of the action, and softer to sit on than fiberglass.

The cockpit is enclosed by a pulpit, and the path forward is atop the cabin or on the trampolines, so a certain amount of agility is required to move forward when necessary. Because of the narrowness of the main hull, shrouds are located on the amas, not close at hand, and the deck is devoid of handrails and lifelines. The trampolines fitted between the hull and amas provide a sturdy, though bouncy, platform.

Corsair outfits boats with high-quality hardware. On the 36, all of the deck gear, including winches, is supplied by Harken or Spinlock.

In its standard configuration she is fitted with Harken B40 self-tailing winches on the cabin top, two Harken B42.2 winches in the cockpit, and two Harken B32.2 self-tailing halyard winches on the mast. Working halyards at the mast instead of leading them aft to the cockpit makes sense, according to multihull sailors, because multihulls sail flatter, and a walk to the mast and back doesn’t present as much of a challenge as it does on a heeling monohull. It also reduces cockpit clutter and friction.

The mainsheet is located at the end of the boom and led to a Harken traveler track that spans the stern, an arrangement that produces excellent sail shape, allows the helmsman to trim the sail, and also reduces the amount of clutter in the cockpit. The system is fitted with a Harken Big Boat Series double-block and tackle led to cockpit winches.

To maximize performance off the breeze, a spinnaker control kit ($3,720) adds two winches in the cockpit, carbon fiber bowsprit , and sheets, blocks, control lines, and cleats necessary to complete the installation.

Corsair is constructing aluminum masts at its factory from extrusions produced by Sparcraft. Our test boat was equipped with a double-spreader rig with swept spreaders and stainless steel wire rigging. At the time of our test, Koch was considering replacing the double spreaders with singles, because, “the second set was redundant.” He has since made that change.

The standard rig is a 3/4 fractional. With the addition of spinnaker gear and bowsprit, a second stay is attached to the mast approximately one foot higher and terminated near the end of the sprit.

The rotating mast is deck-stepped on a ball atop a Delrin bearing that allows it to rotate 45 degrees. Its movement is controlled by a block and tackle arrangement and stainless steel ring on the aft side of the mast. The result is a significantly more aerodynamic presentation of the mainsail to the breeze, which translates to acceleration and speed when sailing to weather or on a reach.

Two steps on the stern provide access for swimmers. Since the rudder is transom-hung, an outboard is located off-center in a hull recess.

Belowdecks When Corsair stretched the F-27 to 31′, owners were rewarded with living spaces large enough to be marginally comfortable on an extended trip. With more stretching, the C-36 still doesn’t have as spacious a main cabin as a 36-foot monohull because of her narrow beam—but she closes the gap significantly.

The accommodations are an excellent example of what can be accomplished using fiberglass and other weight-saving materials, since virtually all of her components are exposed. In fact, there’s so much exposed white in the fiberglass and headliner that only the red cushions and cabin sole provide some relief from the brightness. In addition to concealing wiring, the headliner also acts as a sound deadener. It’s stuck to the overhead with hook-and-loop fasteners. We were concerned about sagging, but found it difficult to remove. If the glue behind the hook-and-loop tapes fails eventually, it will be easy enough to replace.

The area is well lit by two ports on each side of the cabin, and light entering from the companionway. Our test boat had hatches only over the head and the forward berth. In subsequent boats Koch has added a third in the main cabin.

Given more volume below, designers were able to increase standing headroom to 6′ 6″. The saloon measures nearly 6′ from companionway to the head on the port side. A proper C-shaped, elevated dining area, also to port, converts to a 6-foot berth, tapering in width from 41″ to 30″. The galley is to starboard, aft of a second settee that can double as a berth for a small person, and the V- berth.

Stowage space in the boat is at a premium. Although the amas have large storage areas for light gear, accessing those spaces can be a pain, as is true on all cruising trimarans.

The dining table is constructed of fiberglass, but finished to give the appearance of a shiny wood grain. Similarly, the vinyl sole looks like teak, but is a lightweight composite that comes with a 10-year guarantee. Since the boat has no nav station, the dining table is a likely candidate. Odds are, the VHF radio will be mounted on the companionway bulkhead, and instruments on the companionway hatch, close at hand to a navigator working below.

The galley on our test boat was equipped with an optional stainless steel, two-burner propane stove, and double stainless steel sink. A clever arrangement is a recessed faucet that pops up when needed. All are mounted in a fiberglass cabinet with a tiny storage area below. An insulated ice box is standard; refrigeration and pressure hot and cold water are available as options.

The head is a low-maintenance, smoothly finished fiberglass pan measuring approximately 40″ x 35″, consisting of a molded vanity/sink combination with a medicine cabinet outboard, toilet, and handheld shower. It will prove functional, utilitarian, and just large enough for average-sized adults. It will not be confused with the space on a typical 36-foot cruising monohull. The head shares space with a fiberglass shell housing the daggerboard. The shell is so well finished and fitted in as to be nearly invisible. (The daggerboard is constructed of balsa encapsulated in fiberglass.)

The V-berth offers accommodations for two in an enclosed area that has a hatch overhead and Halogen lights and ports on each side. The berth measures 6′ 4″ long on the centerline. It’s 5′ wide at the head, and fitted with 4″ thick cushions. The hull liner is a combination of fabric and shiny fiberglass. Storage and a holding tank are under the berth.

A second berth with a queen-sized mattress is located below the cockpit sole. It’s accessed via two hatches aft of the cockpit, in what would be called the lazarette area, or by removing companionway steps. Two ports provide ventilation at anchor. This is the most spacious sleeping area, and will be fun for kids to climb in and out of (especially since it also hosts the transparent escape hatch). However, the mattress will be ruined quickly if people climb down there with dirty or wet deck shoes, and the space will be noisy if used while underway.

A large storage area under the steps provides a bed for an optional diesel engine. In our view, the 20-hp outboard and a solar panel or two will be the better choice. Don’t overburden a butterfly.

Construction The high cost of Corsair’s boats is attributed to several factors, not the least of which are tooling costs associated with a boat that has more than 30 different moldings, including 10 in the deck and hull, and 11 in the areas belowdecks, as well as two amas, four akas (crossbeams), and all the precision-engineered parts that allow the whole thing to be folded up.

In addition, the company uses high-tech raw materials, including vinylester resins, carbon fiber, double-bias fabrics with Kevlar, and a vacuum-bagging and curing process that relies on precise blends of fiberglass, resin, and catalysts.

Since light weight and high performance are closely related, Koch says hull #1 was built to within 200 pounds of her design weight. Subsequent boats have been further reduced by 100 pounds, mostly by eliminating a set of spreaders and their related parts.

The lamination schedule consists of a layer of NPG gelcoat, a skin layer impregnated with vinylester resin to prevent blistering, and multiple layers of uni- and bi-directional fiberglass. Kevlar is laid in high-stress areas on the bottom, daggerboard trunk, and at bulkheads.

Akas are constructed of layers of fiberglass, carbon fiber, and foam, which increases stiffness. Additional strength and buoyancy in the amas is afforded by watertight bulkheads.

Performance PS editors have sailed most of the Corsair boats over the years, often in racing conditions, and can attest to their speed under sail and their strong construction. This time, we wanted to see if the company could add creature comforts without compromising performance.

Koch’s hopes were for a 15-knot cruiser. “I was surprised,” he told us, “when she sailed at 20 knots during early testing of a prototype in Australia.”

Aside from the long waterline and low wetted surface of the main hull, and the light overall weight of the boat, the biggest contributor to performance is the rotating mast, which supports a square-topped, full-battened mainsail with oversized roach. The advantage of the rotating mast is that it presents a clean, aerodynamic shape to the wind, as opposed to the slab of aluminum of a fixed spar. As we learned during our day-long test sail, trimming the main involves driver and trimmer coordinating their point of sail and mast position. In heavier air, “de- rotating” the mast brings it closer to the apparent wind, flattening the mainsail, and spilling wind to prevent heeling.

We sailed on Biscayne Bay in winds that built from 5 to 15 knots. We had a crew of six—one crewmember stretched out on the V- berth, another snoozing on the trampoline, and four of us trimming sails.

Several manufacturers were testing their new products to see how they performed, using a two-year-old Corsair F-31 as the rabbit. Koch’s goal was to compare the performance of the old and new boats.

From a mechanical standpoint, the boat is easily managed from the cockpit, except that the main is hoisted at the mast. The genoa is on a furler, and main and jib sheets are close at hand.

With Steve Marsh of the Finish Line, a dealer in Stuart, at the helm, we sailed close-hauled in 8-12 knots of wind with boatspeed consistently registering 8-10 knots. She sailed higher and tacked faster than other boats in the fleet, and as quickly as the F-31. She seems to pivot on her daggerboard, and tacked through 95-100°.

When the wind angle moved deeper than 35°, we hoisted a “screacher,” essentially a high-clewed, 180% drifter, and speed increased to 12-15 knots. She heeled 5-10°, carving through a modest chop on the surface. Performance in these conditions was as good or better than the F-31.

The sheeting angle of the headsail is adjusted via a canvas strap attached to the hull beams. It allows the clew position to be moved in and out, much like a barberhauler.

As the wind backed, we punched through small swells by elevating the height of the screacher tack, easing the tack line from the cockpit.

A big difference between monohulls and multihulls is that when a puff hits, most monohulls will use up some of that force by heeling to it, while a good multihull will stay firmly on its feet and use the force for acceleration. The C-36 does this admirably.

Steering through a jibe with a screacher on the sprit-equipped boat is challenging, since the screacher moves between forestay and furler. Once the boat is headed dead downwind and the boom centered, the jibe is completed by quickly turning to weather to fill the sail while the crew tensions the new sheet and the mainsail is eased.

The boat moved easily through the harbor at 5-7 knots with the quiet 20-hp. four-stroke outboard.

Price The current base price for the Corsair 36 is $199,000, including the 20-hp. motor, FOB Chula Vista. In reality, a well-equipped boat will cost closer to $215,000-$225,000, including sails and trailer ($7,638) but without race gear or spinnaker. Options include the propane stove with hot water system, ($875); pressure water ($2,275); Standard Eclipse VHF radio and antenna ($645); spinnaker control kit ($3,720), and screacher controls ($1,969), which require the spinnaker controls.

Conclusion When we first examined Corsair boats years ago, it was with a skeptical eye. While sailing characteristics weren’t questioned, folding tris are complex. We worried about the lightweight construction methods and durability; the toughness of the ama-aka combination; viability as a trailerable vessel, and high price.

Time has alleviated most of those concerns, even the ones about cost, because, in this case, you’re paying for things that work.

The C-36 is certainly fast. Not many boats this size, even other multihulls, will cruise easily at 12-15 knots. She’s also versatile. Her shallow draft offers opportunites to picnic on the beach, or anchor close to shore, away from the mooring field, and yet her foldability means that she can hover in crowded areas when necessary. And she can be towed down the highway for cruising or racing far afield.

Corsair says the boats can be rigged, unloaded, and ready to sail in an hour. Based on real-life observations, we think the time will vary with the size and physical prowess of the crew.

Cockpit seating is large enough to seat six comfortably underway or at the dock. Down below, it’s bright and clean-looking, but creature comforts don’t compare in size or appointments to a middle-of-the-road 36′ monohull equipped with nav station, wine rack, and entertainment center—if that’s your bag. On this boat, the entertainment is found underway.

The high initial cost for trailerable folding trimarans tends to produce sticker shock, since a similar-sized monohull can be purchased for 25% less. On the upside, well-maintained, newer used tris are selling for 75-85% of their original price.

This new boat will appeal to sailors who prefer sleekness and speed to “cushiness,” which is not the same as “comfort.” Aboard boats, comfort is linked to function, and by that definition she’s comfortable enough.

Contact – 877/FASTTRI, www.corsairmarine.com

RELATED ARTICLES MORE FROM AUTHOR

Leave a reply cancel reply.

Log in to leave a comment

Latest Videos

Catalina 380: What You Should Know | Boat Review

• Privacy Policy
• Do Not Sell My Personal Information
• Online Account Activation
• Privacy Manager

Sold Catamaran:

2005 corsair marine corsair 36 (36ft)-vessel summary.

BASIC SUMMARY

Dimensions & specifications, hull and deck configuration, engine details.

• Update Profile
• Email me when price drops
• Do you own a boat like this? Sell it now

Boat Description

The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors to investigate such details as the buyer desired validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice. Photos may not properly reflect the current condition of the actual vessel offered for sale. In some cases stock photographs may have been used.

Mechanical Disclaimer

Engine and generator hours are as of the date of the original listing and are a representation of what the listing broker is told by the owner and/or actual reading of the engine hour meters. The broker cannot guarantee the true hours. It is the responsibility of the purchaser and/or his agent to verify engine hours, warranties implied or otherwise and major overhauls as well as all other representations noted on the listing.

Dinghy Disclaimer

All dinghies are considered separate vessels and should have separate titles and documents. There is no guarantee as to the title of the dinghy on this vessel so Buyer accepts that while he may receive the dinghy included in the transaction, he may not receive the proper title to it.

• 0 No item in your cart
• SUBSCRIPTION
• Classified Ads
• Technical Specifications
• Destinations
• Address book

• All the magazines

Corsair 36: A big folding trimaran from the ‘global village’

The design of the central hull offers both interior volume and good performance under sail! Bravo...

Practical info

• Builder : CORSAIR MARINE INTL
• Technical specifications
• Finance your Corsair 36/37
• Articles about the Corsair 36/37
• Available in issue # 105

Boat Test price $5.00 Inc. tax

Add several tests to your cart

and get an extra discount!

Corsair was created by a New Zealand architect in California, and has built more than 1,200 folding trimarans between 1984 and 2008, which makes it the leader in this segment, along with the Danish Dragonfly. We have just tested the biggest of these trimarans, the Corsair 36...

The 36’ has now been replaced by the Corsair 37, a re-styled version of the same boat. Taking into account the small number of examples present in Europe, we leapt at the chance to test one, whilst waiting to present the 37’ carbon (RS) development.

Aluminium rotating mast, carbon bowsprit and nice Pentex sails by Calvert Sails: the Corsair 36 offers simple but high-performance choices!

The split with the founding architect

In 2000, Ian Farrier left the Chula Vista company that he had created and of which he was the vice-president and the emblematic architect. The disagreement with Paul Koch, the new strong man at Corsair (an Australian who built the Farrier Ostac), led the designer to return to his New Zealand offices, from where he re-launched his own range (F82, 32’, 36’ and 39’), intended for individual (up-market) construction, and Australian and Phillipine (Melvest Yard) production.

A really liveable trimaran which allows you to envisage offshore cruising...

The 36’- 37’: the flagship of a turbulent range

The 36’s characteristics show clearly that it belongs to the Farrier line, and it is obvious that despite the difficulties, the Corsair research and...

To read in full, Buy the boat test

Tags : 

• trimaran , 
• Boat review

What readers think

Post a comment

No comments to show.

Share this article

Follow us on, vous avez ajouté " " à vos favoris., vous avez supprimé " " de vos favoris., in order to add this article to your favorites, please sign in..

Chris Craft Corsair 36

Price au $359,999.

Contact us for more information

Subscribe for all the latest pier 35 boat sales news, events and the latest new and used boats for sale., welcome to pier 35 boat sales.

If you’re looking for a luxury boat for sale in Melbourne, you’re at the right place. Pier 35 Boat Sales is one of the most trusted names in sports cruiser and motor boat sales in Victoria. We specialize in all aspects of boat sales, purchase, marketing, management and brokerage of the finest launches in Australia.

Quick Links

Address & contact.

• Pier 35 Marina Village, Suite 3, 263-329 Lorimer Street, Port Melbourne VIC 3207
• Ample Free Parking Available
• +61 3 9645 1100

Opening Hours

• Monday – Friday: 9:00AM – 5.30PM
• Saturday - 9.30AM – 5:00PM

Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.

• Sailboat Guide

Corsair 36 is a 35 ′ 11 ″ / 11 m trimaran sailboat designed by Corsair Marine and built by Corsair Marine starting in 2002.

Rig and Sails

Auxilary power, accomodations, calculations.

The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.

Classic hull speed formula:

Hull Speed = 1.34 x √LWL

Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio .311 Hull Speed = Max Speed/Length ratio x √LWL

Sail Area / Displacement Ratio

A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.

SA/D = SA ÷ (D ÷ 64) 2/3

• SA : Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
• D : Displacement in pounds.

Ballast / Displacement Ratio

A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.

Ballast / Displacement * 100

Displacement / Length Ratio

A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.

D/L = (D ÷ 2240) ÷ (0.01 x LWL)³

• D: Displacement of the boat in pounds.
• LWL: Waterline length in feet

Comfort Ratio

This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.

Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam 1.33 )

• D: Displacement of the boat in pounds
• LOA: Length overall in feet
• Beam: Width of boat at the widest point in feet

Capsize Screening Formula

This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.

CSV = Beam ÷ ³√(D / 64)

Embed this page on your own website by copying and pasting this code.

• About Sailboat Guide

©2024 Sea Time Tech, LLC

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Folding System

Legendary ability, unbeatable reliability.

Folding and unfolding a Corsair trimaran takes only a minute. With just 4 bolts to remove, it is easily managed by one person, and is normally done while afloat. Simply raise (to fold) or press down (to unfold) the inboard end of one cross beam. It can be done from the safety of the cockpit and only a little force is needed due to the folding system’s carefully balanced geometry, and the movement of the floats being mostly horizontal.

The solid aluminium folding struts have absolute control over the folding motion and prevent flexing or racking. A stainless steel bolt on the inboard end of each beam secures the floats for sailing. Crucially, wingnets remain attached during the folding process – their frictionless fixing allows them to tension themselves appropriately through the folding process. The system is so simple and balanced that Corsair trimarans can even be folded while motoring.

TRAILERING ACROSS CONTINENTS

Corsair Marine trimarans are especially weight-conscious, and sit low on their trailers meaning they have excellent trailering characteristics. They are equally easy to launch, giving you more time on the water, and the ability to expore many more remote cruising grounds or participate in regattas far from home. Some Corsair trimaran models go from trailer to water in 25 minutes, and with practice even the largest boat models can be done in 40 minutes.

Corsair 880 Trimaran | 2022 Boat Review by Multihulls World

Corsair 880 – Drive Out, Fold Out, Thrill Out, Chill Out

Australian Debut of the Corsair 880 at the Sydney International Boat Show

• Folding Corsair Trimarans: Legendary Ability, Unbeatable Reliability
• 5 Reasons Why The Corsair 760 Trimaran Won Multihull Of The Year
• Corsair Range Brochure
• Corsair Community
• Find A Dealer

Tel +84 28 3873 3630

Sales Enquiry:

[email protected]

Customer Service Enquiry:

[email protected]

© 2024 Corsair Marine International. Alls rights reserved.

Privacy Policy

Corsair Coaster

Operating since -

Make: Zamperla Model: Other / Speedy Coaster

Aerial Imagery

Columbia University in the City of New York

Miriam and ira d. wallach art gallery.

• Visitor Information
• Exhibitions
• Publications

Moscow: City, Spectacle, Capital of Photography

April 30–june 21, 2003.

Moscow: City, Spectacle, Capital of Photography , an exhibition of 20th-century photographs of Moscow, opens at Columbia University's Miriam and Ira D. Wallach Art Gallery on Wednesday, April 30, 2003 and remains on display through Saturday, June 21, 2003.

Moscow has been a powerful magnet for many Russian photographers of the 20th century. Moscow: City, Spectacle, Capital of Photography presents the work of 31 photographers, whose images have defined the visual experience of Moscow from the 1920s to the present. Diverse in form and strategy, the 90 photographs chosen for the exhibition trace the history of Russian documentary photography and offer insight into individual practices. From Aleksandr Rodchenko's constructivist visions and Evgenii Khaldei's humanist landscapes to Igor Moukhin's scenes of urban spectacle and alienation in the works of Russia's key 20th-century photographers, Moscow ventures beyond the expected image as a site of famous landmarks, architectural treasures and dramatic lifestyles.

Early 20th-century photographers Boris Ignatovich and Arkadii Shaikhet saw themselves in the vanguard of an emerging mass-media culture, defining with their cameras the visual experience of Soviet modernity. For nearly 70 years, Soviet photography was assigned the duty of maintaining the ideological rigidity of the Soviet State. Yet, as examples of the work of Iakov Khalip, Anatolii Egorov, Mikhail Savin, and Mark Markov-Grinberg show, Soviet photographic practices were much more complex than has been previously acknowledged. The works of these photographers remain intensely compelling to a modernist eye.

Contemporary Russian photographers, such as Lev Melikhov, Valerii Stigneev and Sergei Leontiev, engage with the legacy of the Soviet documentary photography. But for them the documentary is a complex and multivalent genre, which incorporates subjectivity, ambiguity and reflexivity and comments on social and cultural issues without losing sight of the position from which that commentary is made. In the recent photographs by Vladimir Kupriyanov, Igor Moukhin, Anna Gorunova and Pakito Infante, the "real" space of Moscow is replaced by an imaginary and optical spaces of virtuality.

The works in the exhibition are on loan from Moscow's Cultural Center Dom, and many are being shown outside Russia for the first time. In conjunction with the exhibition, the Wallach Art Gallery is publishing an illustrated catalogue with a scholarly essay by the exhibition curator, Nadia Michoustina, a Ph.D. candidate in Columbia University's Department of Slavic Languages. The essay presents a nuanced history of Russian photography of the 20th century, and contributes to an interpretation of extraordinary images.

• Election 2024
• Entertainment
• Newsletters
• Photography
• Press Releases
• Israel-Hamas War
• Russia-Ukraine War
• Global elections
• Asia Pacific
• Latin America
• Middle East
• AP Top 25 College Football Poll
• Movie reviews
• Book reviews
• Financial Markets
• Business Highlights
• Financial wellness
• Artificial Intelligence
• Social Media

Drone attacks in Moscow’s glittering business district leave residents on edge

People stroll at embankment of the Moscow River in Moscow, Russia, Tuesday, Aug. 1, 2023, with the “Moscow City” business district in the background. The glittering towers of the Moscow City business district were once symbols of the Russian capital’s economic boom in the early 2000s. Now they are a sign of its vulnerability, following a series of drone attacks that rattled some Muscovites shaken and brought the war in Ukraine home to the seat of Russian power. (AP Photo/Dmitry Serebryakov)

A couple sit in a park in Moscow, Russia, Tuesday, Aug. 1, 2023, with the “Moscow City” business district in the background. The glittering towers of the Moscow City business district were once symbols of the Russian capital’s economic boom in the early 2000s. Now they are a sign of its vulnerability, following a series of drone attacks that rattled some Muscovites shaken and brought the war in Ukraine home to the seat of Russian power. (AP Photo/Dmitry Serebryakov)

Police officers stand near the Red Square in Moscow, Russia, Tuesday, Aug. 1, 2023. The glittering towers of the Moscow City business district were once symbols of the Russian capital’s economic boom in the early 2000s. Now they are a sign of its vulnerability, following a series of drone attacks that rattled some Muscovites shaken and brought the war in Ukraine home to the seat of Russian power. (AP Photo/Dmitry Serebryakov)

People stroll at the Red Square in Moscow, Russia, Tuesday, Aug. 1, 2023. The glittering towers of the Moscow City business district were once symbols of the Russian capital’s economic boom in the early 2000s. Now they are a sign of its vulnerability, following a series of drone attacks that rattled some Muscovites shaken and brought the war in Ukraine home to the seat of Russian power. (AP Photo/Dmitry Serebryakov)

People sit in a cafe in Moscow, Russia, Tuesday, Aug. 1, The glittering towers of the Moscow City business district were once symbols of the Russian capital’s economic boom in the early 2000s. Now they are a sign of its vulnerability, following a series of drone attacks that rattled some Muscovites shaken and brought the war in Ukraine home to the seat of Russian power. 2023. (AP Photo/Dmitry Serebryakov)

A view of the damaged building is seen in the “Moscow City” business district after a reported drone attack in Moscow, Russia, early Tuesday, Aug. 1, 2023. Ukrainian drones again targeted Moscow and its surroundings early Tuesday morning, the Russian military reported. Two of three launched were shot down outside Moscow, while one crashed into a skyscraper in the Moscow City business district, damaging the building’s facade. (AP Photo)

Investigators examine an area next to damaged building in the “Moscow City” business district after a reported drone attack in Moscow, Russia, early Tuesday, Aug. 1, 2023. Ukrainian drones again targeted Moscow and its surroundings early Tuesday morning, the Russian military reported. Two of three launched were shot down outside Moscow, while one crashed into a skyscraper in the Moscow City business district, damaging the building’s facade. (AP Photo)

• Copy Link copied

The glittering towers of the Moscow City business district dominate the skyline of the Russian capital. The sleek glass-and-steel buildings -- designed to attract investment amid an economic boom in the early 2000s – are a dramatic, modern contrast to the rest of the more than 800-year-old city.

Now they are a sign of its vulnerability, following a series of drone attacks that rattled some Muscovites and brought the war in Ukraine home to the seat of Russian power.

The attacks on Sunday and Tuesday aren’t the first to hit Moscow — a drone even struck the Kremlin harmlessly in May. But these latest blasts, which caused no casualties but blew out part of a section of windows on a high-rise building and sent glass cascading to the streets, seemed particularly unsettling.

“It’s very frightening because you wake up at night hearing explosions,” said a woman who identified herself only as Ulfiya as she walked her dog, adding that she lived in a nearby building. Like other Muscovites interviewed by The Associated Press, she did not identify herself further out of fear of retribution or for her personal safety.

Another resident, who gave her name as Ekaterina, said Tuesday’s blast “sounded like thunder.”

“I think for the first time, I got really scared,” she said. “I don’t understand how people in a war zone can live like this every day and not go mad.”

The Russian Defense Ministry said it shot down two Ukrainian drones outside Moscow and had electronically jammed another, sending it crashing into the IQ-Quarter skyscraper that houses government offices like the Ministry of Economic Development, the Ministry of Digital Development and Communications, and the Ministry of Industry and Trade — the same building that was hit Sunday.

A cordon went up around the building and personnel from the fire department and the Russian Investigative Committee were at the scene. Hours later, residents strolled through the district along the Moscow River or sat on benches in the sunshine. By about 1 p.m. Tuesday, workers were already starting to replace damaged windows.

The business district, a 10-minute subway ride west of the Kremlin, is home to some of Moscow’s flashiest restaurants, offering far-reaching views of the capital and a menu of upscale fare like three types of caviar, shellfish from Russia’s Far East and French cuisine.

But there was no escaping the grim news.

While Russian state television has largely played down the strikes, one channel sandwiched a segment on how Moscow’s air defenses successfully intercepted the drones in between reports highlighting Russian attacks on Ukraine.

Mykhailo Podolyak, an adviser to President Volodymyr Zelenskyy, said in Ukraine that Moscow “is rapidly getting used to a full-fledged war,” without confirming or denying Kyiv’s involvement in the drone attacks that in recent days have struck from the capital to the Crimean Peninsula .

After Sunday’s strike, the Kremlin said security would be ramped up.

Still, the size of the drone that hit the Moscow City district led analysts to question the effectiveness of the capital’s air defenses, suggesting it could have been launched from Ukraine.

“If this is the case, this would be rather embarrassing for Russia’s air defenses. If a drone has been in Russian airspace for hours, air defenses should have picked it up earlier and shot it down earlier,” said Ulrike Franke, an expert in drones and military technology at the European Council on Foreign Relations.

While they haven’t caused much physical damage, bringing the drone campaign to Moscow “blows holes in Russia’s narrative that the war on Ukraine is successful and that it is being prosecuted far away from any consequences for the Russian people themselves,” said Keir Giles, a Russia expert at the Chatham House think tank in London.

“That is something which is going to be harder and harder for Russia’s propaganda machine to explain away,” he said.

A Muscovite who identified himself to the AP only as Eldar summed up the strikes this way: “We attack them, they attack us. And it’s obvious that they will succeed somewhere, and we will succeed somewhere. We should try to strengthen the defense.”

In Odintsovo, where some of the drones were downed about 30 kilometers (18 miles) southwest of the capital, some residents discussed the events on their local Telegram channel.

One woman talked about hearing noises that turned out to be a car or improperly closed trash containers, and seeing what she thought were drones but actually were a flock of birds, a plane and a wind-blown plastic bag.

“How is it possible to live like this?” she asked the group.

“Stop creating panic,” one member admonished her.

“If you hear a noise, be happy because it hasn’t hit you,” added another.

Burrows reported from Tallinn, Estonia.

Follow AP’s coverage of the war in Ukraine at https://apnews.com/hub/russia-ukraine